Press the "MODE" key on the operation panel several times to display "P.0" and parameter setting screen. Then turn the s

Specific settings are not required, however, when replacing the FR-E500, check that Pr.146 (Built-in potentiometer switc

When using the setting dial to set the frequency, turn the dial and press the "SET" key while the desired value flickers

Turning ON/OFF the output side during operation causes open/close surges that may trigger the protective function (again

Set it to "13" (Constant-torque).

After setting Pr.340 to "10", you need to power OFF then ON the inverter to make the new setting enabled because you are

The first priority window of the monitor may be set to the current.When the current is displayed on the monitor (the uni

Set Pr.3 (Base frequency) and Pr.18 (High speed maximum frequency) to "340 Hz", Pr.19 (Base frequency voltage) to "200 V

To accept the current signal, the terminals AU (current input selection) and SD must be short-circuited. Check it.Note t

Since the external thermal prevents the motor from being overheated, install it between the output terminal of the inver

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-A700

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-A700 ]

241-250 of Total 352

prev 25 / 36page next

Parameter

Press the "MODE" key on the operation panel several times to display "P.0" and parameter setting screen. Then turn the setting dial to display "C..." screen ... More Details >>
- No：21336
- Release Date：2018/08/22 16:27
FR-PA07

Specific settings are not required, however, when replacing the FR-E500, check that Pr.146 (Built-in potentiometer switchover) is not set to "0". If it is "0... More Details >>
- No：21363
- Release Date：2018/08/22 16:27
RUN blinks

When using the setting dial to set the frequency, turn the dial and press the "SET" key while the desired value flickers. (The value and "F" flicker alternat... More Details >>
- No：21692
- Release Date：2018/08/22 16:28
Electromagnetic contactor

Turning ON/OFF the output side during operation causes open/close surges that may trigger the protective function (against overcurrent or overvoltage) of the... More Details >>
- No：21725
- Release Date：2018/08/22 16:29
Auto tuning

Set it to "13" (Constant-torque).　　 More Details >>
- No：21752
- Release Date：2018/08/22 16:29
NET mode

After setting Pr.340 to "10", you need to power OFF then ON the inverter to make the new setting enabled because you are setting the operation upon power-on.... More Details >>
- No：21759
- Release Date：2018/08/22 16:29
Monitor indicator

The first priority window of the monitor may be set to the current.When the current is displayed on the monitor (the unit is "A"), press "SET" to switch to t... More Details >>
- No：21765
- Release Date：2018/08/22 16:29
Frequency setting

Set Pr.3 (Base frequency) and Pr.18 (High speed maximum frequency) to "340 Hz", Pr.19 (Base frequency voltage) to "200 V", Pr.125 (Terminal 2 frequency setti... More Details >>
- No：21789
- Release Date：2018/08/22 16:29
Frequency setting

To accept the current signal, the terminals AU (current input selection) and SD must be short-circuited. Check it.Note that this terminal AU is not prepared ... More Details >>
- No：21799
- Release Date：2018/08/22 16:29
External installationRated current

Since the external thermal prevents the motor from being overheated, install it between the output terminal of the inverter and the motor.The rated current i... More Details >>
- No：21817
- Release Date：2018/08/22 16:29

241-250 of Total 352

Inquiries

page top