Pr.1 (Maximum frequency) or Pr.18 (High speed maximum frequency).

The error LED on the master side of the programmable controller blinks (faulty station present).According to the SW80 st

Set Pr.79 to "2" (external operation mode).

Yes. However, write the setting data to the RAM of the inverter.Set RWw1 in the setting value and turn ON the frequency

The start commands cannot be input from both sources simultaneously because the operation command source is specified.Yo

If Pr.544 (CC-Link extended setting) is set to other than "0", you do not need to change Pr.544 (CC-Link extended settin

Use Pr.542 to set the station number and Pr.543 to set the baud rate.To set the baud rate to 10 Mbps, set Pr.543 to "4".

When the frequency is set using the setting dial, it is not necessary to set it again.The inverter memorizes the setting

Yes. (Terminal SDs are connected with each other inside of the inverter.)

Set Pr.79 (Operation mode) to "1" (PU operation mode) and change Pr.161 (Frequency setting/key lock operation selection)

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-A700

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-A700 ]

71-80 of Total 352

prev 8 / 36page next

Frequency setting

Pr.1 (Maximum frequency) or Pr.18 (High speed maximum frequency).　　 More Details >>
- No：21805
- Release Date：2018/08/22 16:29
Programmable controller

The error LED on the master side of the programmable controller blinks (faulty station present).According to the SW80 station information, an error flag is a... More Details >>
- No：21813
- Release Date：2018/08/22 16:29
Operation mode setting value

Set Pr.79 to "2" (external operation mode).　　　 More Details >>
- No：21818
- Release Date：2018/08/22 16:29
CC-Link

Yes. However, write the setting data to the RAM of the inverter.Set RWw1 in the setting value and turn ON the frequency setting command RYD.To continuously s... More Details >>
- No：21825
- Release Date：2018/08/22 16:29
CC-Link

The start commands cannot be input from both sources simultaneously because the operation command source is specified.You can switch the command source as ne... More Details >>
- No：21828
- Release Date：2018/08/22 16:29
CC-Link

If Pr.544 (CC-Link extended setting) is set to other than "0", you do not need to change Pr.544 (CC-Link extended setting).Write the extended setting of the ... More Details >>
- No：21834
- Release Date：2018/08/22 16:29
CC-Link

Use Pr.542 to set the station number and Pr.543 to set the baud rate.To set the baud rate to 10 Mbps, set Pr.543 to "4". More Details >>
- No：21839
- Release Date：2018/08/22 16:29
Frequency setting

When the frequency is set using the setting dial, it is not necessary to set it again.The inverter memorizes the setting value internally even after the powe... More Details >>
- No：21842
- Release Date：2018/08/22 16:29
Control terminal

Yes. (Terminal SDs are connected with each other inside of the inverter.) More Details >>
- No：21845
- Release Date：2018/08/22 16:29
PU operation

Set Pr.79 (Operation mode) to "1" (PU operation mode) and change Pr.161 (Frequency setting/key lock operation selection) to "1" (potentiometer mode).　　 More Details >>
- No：21863
- Release Date：2018/08/22 16:29

71-80 of Total 352

Inquiries

page top