You can select from the output power (in 0.01 kW units) and cumulative energy (in 1 kWh/0.01 kWh units).

You can start/stop operation, set the frequency, read/write parameters, and monitor the inverter via CC-Link communicati

1. Set Pr.162 to "10" (Frequency search at every start).2. You can ignore the setting if the motor excitation current is

Yes. Set the first monitor code in the lower 8 bits and the second monitor code in the upper 8 bits of RWwn.Set H6F to t

The start commands cannot be input from both sources simultaneously because the operation command source is specified.Yo

"n" in the address RWwn indicates a value determined by the station number setting.

When using the geared motor GM-S(B), set Pr.71 to "13" and also set Pr.9, Pr.80, and Pr.81.Perform auto tuning as requir

Use Pr.542 to set the station number and Pr.543 to set the baud rate.To set the baud rate to 10 Mbps, set Pr.543 to "4".

If Pr.340 (Communication startup mode selection) and Pr.79 (Operation mode selection) are set so that the inverter start

Connect the wire to the optional FR-A7NC's terminal block. (The terminal block is detachable.)

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-A700

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-A700 ]

81-90 of Total 351

prev 9 / 36page next

CC-Link

You can select from the output power (in 0.01 kW units) and cumulative energy (in 1 kWh/0.01 kWh units). More Details >>
- No：21885
- Release Date：2018/08/22 16:29
CC-Link

You can start/stop operation, set the frequency, read/write parameters, and monitor the inverter via CC-Link communication. More Details >>
- No：21901
- Release Date：2018/08/22 16:29
Coasting

1. Set Pr.162 to "10" (Frequency search at every start).2. You can ignore the setting if the motor excitation current is unknown. More Details >>
- No：21718
- Release Date：2018/08/22 16:29
CC-Link

Yes. Set the first monitor code in the lower 8 bits and the second monitor code in the upper 8 bits of RWwn.Set H6F to the first monitor code, and H70 to the... More Details >>
- No：21824
- Release Date：2018/08/22 16:29
CC-Link

The start commands cannot be input from both sources simultaneously because the operation command source is specified.You can switch the command source as ne... More Details >>
- No：21828
- Release Date：2018/08/22 16:29
CC-Link

"n" in the address RWwn indicates a value determined by the station number setting. More Details >>
- No：21867
- Release Date：2018/08/22 16:29
Advanced magnetic flux vector control

When using the geared motor GM-S(B), set Pr.71 to "13" and also set Pr.9, Pr.80, and Pr.81.Perform auto tuning as required. Perform auto tuning as required. ... More Details >>
- No：21756
- Release Date：2018/08/22 16:29
CC-Link

Use Pr.542 to set the station number and Pr.543 to set the baud rate.To set the baud rate to 10 Mbps, set Pr.543 to "4". More Details >>
- No：21839
- Release Date：2018/08/22 16:29
CC-Link

If Pr.340 (Communication startup mode selection) and Pr.79 (Operation mode selection) are set so that the inverter starts CC-Link operation from power-on and... More Details >>
- No：21840
- Release Date：2018/08/22 16:29
CC-Link

Connect the wire to the optional FR-A7NC's terminal block. (The terminal block is detachable.) More Details >>
- No：21875
- Release Date：2018/08/22 16:29

81-90 of Total 351

Inquiries

page top