Priorities are: Low speed (RL) > Middle speed (RM) > High speed (RH).For example, if the low speed (RL) and middle

It is the standardized Mini-B connector.

Set Pr.125 (Terminal 2 frequency setting gain frequency) = "90 Hz".This changes the frequency with the potentiometer tur

Set Pr.340 (Communication startup mode selection) to "10".The operation mode can be switched between PU and NET by assig

This is due to specifications that multi-speed selection is prioritized and setting with the setting dial is ignored.The

From the LED, it is considered that the operation mode Pr.79 is set to "3".The PU and EXT LEDs turn ON with this setting

You can connect a 1 mA full scale ammeter with internal resistance 300 Ω or lower.

Assign X16 signal, and set Pr.79 to "0", to switch the operation mode with turning ON/OFF X16 signal.

The FR Configurator FR-SW3-SETUP-WJ can only allow for test operation.Since this is a tool to support the system launch

Check if signals that are ON when the programmable controller's transistor output starts are always ON.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-F700

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-F700 ]

11-20 of Total 296

prev 2 / 30page next

Multi-speed setting

Priorities are: Low speed (RL) > Middle speed (RM) > High speed (RH).For example, if the low speed (RL) and middle speed (RM) signals are input simulta... More Details >>
- No：21772
- Release Date：2018/08/22 16:29
Connection cable of FR-Configurator

It is the standardized Mini-B connector. More Details >>
- No：21312
- Release Date：2018/08/22 16:26
Frequency setting

Set Pr.125 (Terminal 2 frequency setting gain frequency) = "90 Hz".This changes the frequency with the potentiometer turned to the maximum position (at 5 V i... More Details >>
- No：21909
- Release Date：2018/08/22 16:30
Switching between PU and NET operation modes

Set Pr.340 (Communication startup mode selection) to "10".The operation mode can be switched between PU and NET by assigning X65 (PU-NET operation switching)... More Details >>
- No：21878
- Release Date：2018/08/22 16:29
Frequency setting

This is due to specifications that multi-speed selection is prioritized and setting with the setting dial is ignored.The setting dial is effective when multi... More Details >>
- No：21843
- Release Date：2018/08/22 16:29
Frequency setting

From the LED, it is considered that the operation mode Pr.79 is set to "3".The PU and EXT LEDs turn ON with this setting.In this state, you cannot change bet... More Details >>
- No：21741
- Release Date：2018/08/22 16:29
Terminal FM

You can connect a 1 mA full scale ammeter with internal resistance 300 Ω or lower. More Details >>
- No：21680
- Release Date：2018/08/22 16:28
Switching between External operation mode and PU operation mode

Assign X16 signal, and set Pr.79 to "0", to switch the operation mode with turning ON/OFF X16 signal. More Details >>
- No：21288
- Release Date：2018/08/22 16:26
FR-Configurator

The FR Configurator FR-SW3-SETUP-WJ can only allow for test operation.Since this is a tool to support the system launch and maintenance, it is not designed f... More Details >>
- No：21914
- Release Date：2018/08/22 16:30
Transistor output module of the programmable controller

Check if signals that are ON when the programmable controller's transistor output starts are always ON. More Details >>
- No：21811
- Release Date：2018/08/22 16:29

11-20 of Total 296

Inquiries

page top