Setting Pr.79 (Operation mode) to "6" sets the switchover mode. Pressing the "PU/EXT" key on the operation panel during

Set the rated motor current to Pr.9. It is the heat protection setting for the motor, and thus the inverter does not shu

Set Pr.338 (Communication command source) to "0" to give a start command from "NET". Set Pr.339 (Speed command source) t

You can use an external potentiometer and multi-speed operation together.When an external potentiometer signal input and

The possible causes of the error UVT are as follows.- Low power supply voltage - Insufficient power supply capacity - Da

You can use optional items, such as enclosure surface operation panel FR-PA07 and parameter unit FR-PU07.Use the PU conn

Since Pr.125 (Terminal 2 frequency setting gain frequency) is initially set to 60 Hz, change it to 85 Hz.

Set the rated frequency of the motor used to it.

Even after setting Pr.340 to "10", the change is reflected after resetting the power supply.Perform the power reset.Sinc

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-F700

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-F700 ]

31-40 of Total 296

prev 4 / 30page next

Switching External operation, PU operation

Setting Pr.79 (Operation mode) to "6" sets the switchover mode. Pressing the "PU/EXT" key on the operation panel during External operation switches the mode ... More Details >>
- No：21289
- Release Date：2018/08/22 16:26
Fault output terminal A, B, and C

Set the rated motor current to Pr.9. It is the heat protection setting for the motor, and thus the inverter does not shutoff immediately at the specified cur... More Details >>
- No：21324
- Release Date：2018/08/22 16:27
Start command

Set Pr.338 (Communication command source) to "0" to give a start command from "NET". Set Pr.339 (Speed command source) to "1" to make a frequency setting fro... More Details >>
- No：21285
- Release Date：2018/08/22 16:26
Using external potentiometer and multi-speed operation together

You can use an external potentiometer and multi-speed operation together.When an external potentiometer signal input and multi-speed setting occur simultaneo... More Details >>
- No：21920
- Release Date：2018/08/22 16:30
Error "E.UVT" (undervoltage protection)

The possible causes of the error UVT are as follows.- Low power supply voltage - Insufficient power supply capacity - Damage or failure Check the power suppl... More Details >>
- No：21295
- Release Date：2018/08/22 16:26
Driving a single-phase motor

No, it cannot. More Details >>
- No：21253
- Release Date：2018/08/22 16:26
CC-Link

You can use optional items, such as enclosure surface operation panel FR-PA07 and parameter unit FR-PU07.Use the PU connector of the inverter for connection.... More Details >>
- No：21832
- Release Date：2018/08/22 16:29
Frequency setting

Since Pr.125 (Terminal 2 frequency setting gain frequency) is initially set to 60 Hz, change it to 85 Hz. More Details >>
- No：21907
- Release Date：2018/08/22 16:30
Base frequency setting value

Set the rated frequency of the motor used to it.　 More Details >>
- No：21814
- Release Date：2018/08/22 16:29
Switching between PU and NET operations

Even after setting Pr.340 to "10", the change is reflected after resetting the power supply.Perform the power reset.Since changes to the communication parame... More Details >>
- No：21696
- Release Date：2018/08/22 16:28

31-40 of Total 296

Inquiries

page top