No. Check the parameter setting of the A500(L), and then adjust the parameter setting of the A800 to those of the A500(L

The speed fluctuation ratio under Advanced magnetic flux vector control of the FR-A500 is as follows. Without encoder: ±

After inputting the start signal performing the tuning, output the output frequency. The tuning ends in approximately 5

For the general-purpose inverter, the motor stop cannot be detected accurately because the actual motor speed from a mot

1. The limit of the parameter writing is 100,000 times. 2. Parameter error occurs. Since the data in the ROM may be brok

1. When the inverter power supply is turned OFF, the inverter is disconnected from the CC-Link network. However, since t

Answer to question 1 When the CC-Link option goes faulty, OPT (option error) occurs and the inverter's fault output is t

You can use the regular terminal block wire functions during CC-Link operation. Set Pr.338 (Operation command source) a

No. Although the carrier frequency increases or decreases the switching count, the switching speed is the OFF-to-ON spee

When the wire between the 400 V inverter and motor is long (20 m or longer), surge voltage occurs momentarily. This volt

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-A500

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FREQROL-A500

Common(1)

FAQ within [ FREQROL-A500 ]

1-10 of Total 123

prev 1 / 13page next

FR-A800

No. Check the parameter setting of the A500(L), and then adjust the parameter setting of the A800 to those of the A500(L). For the details, refer to the repl... More Details >>
- No：21108
- Release Date：2018/08/22 16:25
- Category： FREQROL-A800 , FREQROL-A500
Vector control of the inverter

The speed fluctuation ratio under Advanced magnetic flux vector control of the FR-A500 is as follows. Without encoder: ±1% With encoder (with A5AP): ±0. 02 %... More Details >>
- No：21369
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Magnetic flux and tuning

After inputting the start signal performing the tuning, output the output frequency. 　The tuning ends in approximately 500 ms in maximum after started. Durin... More Details >>
- No：21372
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Operation of the motor with a brake

For the general-purpose inverter, the motor stop cannot be detected accurately because the actual motor speed from a motor is not input. In general, the RUN ... More Details >>
- No：21375
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Is the number of writing times of the parameter memory limited?

1. The limit of the parameter writing is 100,000 times. 2. Parameter error occurs. Since the data in the ROM may be broken, the inverter may become unavailab... More Details >>
- No：21385
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Countermeasures when input power supply is turned off upon equipment fault

1. When the inverter power supply is turned OFF, the inverter is disconnected from the CC-Link network. However, since the CC-Link master station has the aut... More Details >>
- No：21390
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-E500
Using FR-A540 inverter on CC-Link

Answer to question 1 When the CC-Link option goes faulty, OPT (option error) occurs and the inverter's fault output is triggered. When communication is lost ... More Details >>
- No：21391
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Functions available when using inverter on CC-Link

You can use the regular terminal block wire functions during CC-Link operation. 　Set Pr.338 (Operation command source) and Pr.339 (Speed command source) to e... More Details >>
- No：21393
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Surge voltage of 400 V inverter

No. Although the carrier frequency increases or decreases the switching count, the switching speed is the OFF-to-ON speed of the IGBT element of the inverter... More Details >>
- No：21401
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-F500 , FREQROL-A024 , FREQROL-E500 , FREQROL-V200 , FREQROL-A200 , FREQROL-S500 , FREQROL-A100
Surge voltage of 400 V motor

When the wire between the 400 V inverter and motor is long (20 m or longer), surge voltage occurs momentarily. This voltage is as two or more times as the DC... More Details >>
- No：21404
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-F500 , FREQROL-A024 , FREQROL-E500 , FREQROL-V200 , FREQROL-A200 , FREQROL-A100

1-10 of Total 123

Inquiries

page top