You can input current from the terminal AM of the inverter to the programmable controller (for A/D conversion) and contr

1. Pr.1 and 18 limit the output to 120 Hz. Use Pr.18 to change the maximum frequency. 2. If you want to output the binar

Keep 1 cm or more of clearance for 3.7 K or smaller, and 5 cm or more for 5.5 K or larger.If the clearance is too small,

The wiring length of the start signal (STF etc.) is 30 m or less. The circuit voltage of the control input signals (term

1. The output frequency satisfies the "control specification/frequency precision" even when the power supply voltage cha

1. To perform emergency stop, it is recommended to have the motor coast and stop it using a mechanical brake.In this cas

You can use the Hioki Memory HiCorder and clamp-on AC/DC high tester.You can observe the inverter's frequency in one of

1. How much is the sensitivity current? When the sum of the three-phase output current of the inverter reaches approxima

To supply power via R1 and S1, 60 VA or higher is necessary for 22K or lower and 80 VA or higher is necessary for 30K to

For the combination of the FR-A500 + FR-A5NC, Pr.338 and Pr.339 are used to specify whether the external signals or CC-L

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-A500

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FREQROL-A500

Common(1)

FAQ within [ FREQROL-A500 ]

21-30 of Total 123

prev 3 / 13page next

Load current limit of inverter

You can input current from the terminal AM of the inverter to the programmable controller (for A/D conversion) and control the speed with the software of the... More Details >>
- No：21419
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Digital input and maximum frequency

1. Pr.1 and 18 limit the output to 120 Hz. Use Pr.18 to change the maximum frequency. 2. If you want to output the binary input as is, setting Pr.304 = 1 (Bi... More Details >>
- No：22098
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Plug-in Options , FREQROL-A500
Installation clearance of inverters

Keep 1 cm or more of clearance for 3.7 K or smaller, and 5 cm or more for 5.5 K or larger.If the clearance is too small, the cooling effect is lowered. Secur... More Details >>
- No：22046
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Remote operation of the inverter

The wiring length of the start signal (STF etc.) is 30 m or less. The circuit voltage of the control input signals (terminal STF etc.) is 24 VDC and the volt... More Details >>
- No：21380
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Speed change due to power supply voltage fluctuation

1. The output frequency satisfies the "control specification/frequency precision" even when the power supply voltage changes, but the output voltage cannot r... More Details >>
- No：22069
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-E500
Inverter general matters

1. To perform emergency stop, it is recommended to have the motor coast and stop it using a mechanical brake.In this case, the output stop (MRS) signal is in... More Details >>
- No：22103
- Release Date：2018/08/22 16:31
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-E500
Inverter

You can use the Hioki Memory HiCorder and clamp-on AC/DC high tester.You can observe the inverter's frequency in one of the following two methods:1. Attach t... More Details >>
- No：22082
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-E500
Output side earth (ground) fault overcurrent protection

1. How much is the sensitivity current? When the sum of the three-phase output current of the inverter reaches approximately 70% of the inverter rated curren... More Details >>
- No：21394
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-A024 , FREQROL-E500
Inverter control power supply

To supply power via R1 and S1, 60 VA or higher is necessary for 22K or lower and 80 VA or higher is necessary for 30K to 55K.Note that the rush current of ap... More Details >>
- No：22043
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
External wiring for CC-Link operation

For the combination of the FR-A500 + FR-A5NC, Pr.338 and Pr.339 are used to specify whether the external signals or CC-Link commands are used to set the runn... More Details >>
- No：21973
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-E500

21-30 of Total 123

Inquiries

page top