When using the FR-A540-3.7K in Advanced magnetic flux vector control, operating the motor continuously under the 100% to

You can install the operation panel FR-DU04 (or parameter unit FR-PU04) on the enclosure surface by connecting it with t

The reset signal does not damage the inverter.It seems that the inverter went faulty due to other reasons.Mitsubishi Ele

Similarly to the FR-A220, single-phase power supply operation is possible by reducing the inverter's output current.Ensu

The speed fluctuation ratio under Advanced magnetic flux vector control of the FR-A500 is as follows. Without encoder: ±

Answer to question 1 When the CC-Link option goes faulty, OPT (option error) occurs and the inverter's fault output is t

You can input current from the terminal AM of the inverter to the programmable controller (for A/D conversion) and contr

There is a 10 ms delay after the inverter recognizes the start command (STF OR STR) before it starts decelerating. The d

You can calculate the torque from the power. From the general equation: Pout = ωn × TT = (Pout × τ)/ωnPout: Measured va

1. Maximum torque available for output from the motor when combined with an inverter for a short period of time (1 minut

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-A500

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FREQROL-A500

Common(1)

FAQ within [ FREQROL-A500 ]

31-40 of Total 123

prev 4 / 13page next

Motor heat generation at low-speed operation

When using the FR-A540-3.7K in Advanced magnetic flux vector control, operating the motor continuously under the 100% torque at up to 3 Hz does not cause a h... More Details >>
- No：21496
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Installing parameter unit outside control panel

You can install the operation panel FR-DU04 (or parameter unit FR-PU04) on the enclosure surface by connecting it with the inverter via a cable.To do this, d... More Details >>
- No：22044
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Reset command during operation

The reset signal does not damage the inverter.It seems that the inverter went faulty due to other reasons.Mitsubishi Electric FA Center can inspect the inver... More Details >>
- No：22065
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Operation by single-phase power supply

Similarly to the FR-A220, single-phase power supply operation is possible by reducing the inverter's output current.Ensure that the output current is smaller... More Details >>
- No：22107
- Release Date：2018/08/22 16:31
- Category： Inverters-FREQROL , FREQROL-A500
Vector control of the inverter

The speed fluctuation ratio under Advanced magnetic flux vector control of the FR-A500 is as follows. Without encoder: ±1% With encoder (with A5AP): ±0. 02 %... More Details >>
- No：21369
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Using FR-A540 inverter on CC-Link

Answer to question 1 When the CC-Link option goes faulty, OPT (option error) occurs and the inverter's fault output is triggered. When communication is lost ... More Details >>
- No：21391
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Load current limit of inverter

You can input current from the terminal AM of the inverter to the programmable controller (for A/D conversion) and control the speed with the software of the... More Details >>
- No：21419
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Inverter signal input speed

There is a 10 ms delay after the inverter recognizes the start command (STF OR STR) before it starts decelerating. The delay is 10 ms. A delay of 100 ms is i... More Details >>
- No：21445
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
How can I calculate the processing torque from the measured power?

You can calculate the torque from the power. 　From the general equation: Pout = ωn × TT = (Pout × τ)/ωnPout: Measured valueωn: Actual motor shaft angular fre... More Details >>
- No：21475
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , Others , FREQROL-A500
Term definition and advanced magnetic flux control

1. Maximum torque available for output from the motor when combined with an inverter for a short period of time (1 minute or less). 　　It depends on the contr... More Details >>
- No：21541
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500

31-40 of Total 123

Inquiries

page top