To supply power via R1 and S1, 60 VA or higher is necessary for 22K or lower and 80 VA or higher is necessary for 30K to

To change the running frequency while the frequency command is input to the terminal 2, adjust the parameters in the fol

Installing the high power factor converter brings the power factor improving effect of 99% or higher.Therefore, when the

It seems that there is a read error for 20 mA DC inside the inverter.Setting Pr.905 to 50 Hz while 20 mA DC is actually

Change Pr.18 (High speed maximum frequency) to 400 Hz.If you are using the analog command to set the frequency, calibrat

1. Such a behavior does not usually happen. (1) The operation command (STF) is not input, contact faults are present, o

1. Maximum torque available for output from the motor when combined with an inverter for a short period of time (1 minut

"8" display in offline auto tuning means forced stop by the operator. This means that you stopped operation before tunin

If the phase A and phase B are connected reversely, encoder feedback control is not performed. Instead, the inverter is

When using the FR-A540-3.7K in Advanced magnetic flux vector control, operating the motor continuously under the 100% to

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-A500

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FREQROL-A500

Common(1)

FAQ within [ FREQROL-A500 ]

31-40 of Total 123

prev 4 / 13page next

Inverter control power supply

To supply power via R1 and S1, 60 VA or higher is necessary for 22K or lower and 80 VA or higher is necessary for 30K to 55K.Note that the rush current of ap... More Details >>
- No：22043
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Changing main speed at analog signal input

To change the running frequency while the frequency command is input to the terminal 2, adjust the parameters in the following steps:1. Change Pr.77 to "2".2... More Details >>
- No：22025
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Power factor improving effect by option

Installing the high power factor converter brings the power factor improving effect of 99% or higher.Therefore, when the high power factor converter is used,... More Details >>
- No：22020
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-F500 , FREQROL-E500 , FREQROL-V200 , FREQROL-A200 , FREQROL-S500 , FREQROL-A100
Speed control failure due to 20 mA from DC 4

It seems that there is a read error for 20 mA DC inside the inverter.Setting Pr.905 to 50 Hz while 20 mA DC is actually flowing between the terminals 4 and 5... More Details >>
- No：21998
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-F500 , FREQROL-E500 , FREQROL-A200 , FREQROL-A100
400 Hz output setting

Change Pr.18 (High speed maximum frequency) to 400 Hz.If you are using the analog command to set the frequency, calibrate the 400 Hz frequency with Pr.903. More Details >>
- No：21931
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Inverter output stop

1. Such a behavior does not usually happen. 　(1) The operation command (STF) is not input, contact faults are present, or wire is broken. 　(2) The output shu... More Details >>
- No：21552
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500
Term definition and advanced magnetic flux control

1. Maximum torque available for output from the motor when combined with an inverter for a short period of time (1 minute or less). 　　It depends on the contr... More Details >>
- No：21541
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500
Overcurrent at low speed

"8" display in offline auto tuning means forced stop by the operator. This means that you stopped operation before tuning completes. 　With this forced stop, ... More Details >>
- No：21527
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500
Encoder feedback control wire

If the phase A and phase B are connected reversely, encoder feedback control is not performed. Instead, the inverter is operated in normal control (V/F contr... More Details >>
- No：21524
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500
Motor heat generation at low-speed operation

When using the FR-A540-3.7K in Advanced magnetic flux vector control, operating the motor continuously under the 100% torque at up to 3 Hz does not cause a h... More Details >>
- No：21496
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500

31-40 of Total 123

Inquiries

page top