When you use a long wire between the inverter and motor, pay attention to the following: 1. Since the voltage supplied t

When using the FR-A540-3.7K in Advanced magnetic flux vector control, operating the motor continuously under the 100% to

You cannot disable the error display. The OC1 overcurrent alarm is displayed. The condition to display this alarm is tha

Since a large load is applied to the motor when the electromagnetic clutch turns on, overcurrent may occur if the load i

The inverter does not have a function to limit the current at 0 Hz.Although it has the DC injection brake, it is intende

1. You can implement stop-on-contact.2. When implementing stop-on-contact, use the inverter to decelerate the motors to

Keep 1 cm or more of clearance for 3.7 K or smaller, and 5 cm or more for 5.5 K or larger.If the clearance is too small,

The reset signal does not damage the inverter.It seems that the inverter went faulty due to other reasons.Mitsubishi Ele

Similarly to the FR-A220, single-phase power supply operation is possible by reducing the inverter's output current.Ensu

There is a 10 ms delay after the inverter recognizes the start command (STF OR STR) before it starts decelerating. The d

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-A500

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FREQROL-A500

Common(1)

FAQ within [ FREQROL-A500 ]

41-50 of Total 119

prev 5 / 12page next

Long motor wiring

When you use a long wire between the inverter and motor, pay attention to the following: 1. Since the voltage supplied to the motor terminal is reduced due t... More Details >>
- No：21441
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Motor heat generation at low-speed operation

When using the FR-A540-3.7K in Advanced magnetic flux vector control, operating the motor continuously under the 100% torque at up to 3 Hz does not cause a h... More Details >>
- No：21496
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Using control power supply

You cannot disable the error display. The OC1 overcurrent alarm is displayed. The condition to display this alarm is that the main circuit power supply is OF... More Details >>
- No：21535
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500
Clutch connection of load

Since a large load is applied to the motor when the electromagnetic clutch turns on, overcurrent may occur if the load is heavy. To ensure that the rated cur... More Details >>
- No：21955
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-E500
Motor retention at 0 Hz

The inverter does not have a function to limit the current at 0 Hz.Although it has the DC injection brake, it is intended to improve the braking capability b... More Details >>
- No：22002
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Stop-on-contact control

1. You can implement stop-on-contact.2. When implementing stop-on-contact, use the inverter to decelerate the motors to reduce the impact upon stop-on-contac... More Details >>
- No：22041
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Installation clearance of inverters

Keep 1 cm or more of clearance for 3.7 K or smaller, and 5 cm or more for 5.5 K or larger.If the clearance is too small, the cooling effect is lowered. Secur... More Details >>
- No：22046
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Reset command during operation

The reset signal does not damage the inverter.It seems that the inverter went faulty due to other reasons.Mitsubishi Electric FA Center can inspect the inver... More Details >>
- No：22065
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Operation by single-phase power supply

Similarly to the FR-A220, single-phase power supply operation is possible by reducing the inverter's output current.Ensure that the output current is smaller... More Details >>
- No：22107
- Release Date：2018/08/22 16:31
- Category： Inverters-FREQROL , FREQROL-A500
Inverter signal input speed

There is a 10 ms delay after the inverter recognizes the start command (STF OR STR) before it starts decelerating. The delay is 10 ms. A delay of 100 ms is i... More Details >>
- No：21445
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500

41-50 of Total 119

Inquiries

page top