You can start/stop operation, set the frequency, read/write parameters, and monitor the inverter via CC-Link communicati

No problem. The inverter actually occupies the reserved bits and does not use them.

Pr.338 is for the communication operation command source at communication operation and specifies the command source to

Set Pr.338 (Operation command source) to "1" (external terminal).Set Pr.339 (Speed command source) to "0" (communication

You can use the setting dial together with the terminal 4.Set Pr.79 (Operation mode) to "3" (Combined operation mode) an

Yes. However, write the setting data to the RAM of the inverter.Set RWw1 in the setting value and turn ON the frequency

It seems that calibration for 20 mA current signal input is not correct.Use the calibration parameters "126" and "C7" to

Set Pr.52 (DU/PU main display data selection) to "5".This allows for displaying the setting frequency on the voltage mon

Pr.1 (Maximum frequency) and Pr.18 (Maximum frequency).

Set Pr.125 (Terminal 2 frequency setting gain frequency) to "50 Hz".Set Pr.1 (Maximum frequency) to "50 Hz".

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-F700P

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-F700P ]

111-120 of Total 294

prev 12 / 30page next

CC-Link

You can start/stop operation, set the frequency, read/write parameters, and monitor the inverter via CC-Link communication. More Details >>
- No：21901
- Release Date：2018/08/22 16:29
CC-Link

No problem. The inverter actually occupies the reserved bits and does not use them. More Details >>
- No：21890
- Release Date：2018/08/22 16:29
Running frequency setting

Pr.338 is for the communication operation command source at communication operation and specifies the command source to supply the start signal.Pr.339 is for... More Details >>
- No：21880
- Release Date：2018/08/22 16:29
Frequency setting

Set Pr.338 (Operation command source) to "1" (external terminal).Set Pr.339 (Speed command source) to "0" (communication).Check the setting of Pr.79 for oper... More Details >>
- No：21869
- Release Date：2018/08/22 16:29
Frequency setting

You can use the setting dial together with the terminal 4.Set Pr.79 (Operation mode) to "3" (Combined operation mode) and assign the AU signal to an unused t... More Details >>
- No：21856
- Release Date：2018/08/22 16:29
CC-Link

Yes. However, write the setting data to the RAM of the inverter.Set RWw1 in the setting value and turn ON the frequency setting command RYD.To continuously s... More Details >>
- No：21825
- Release Date：2018/08/22 16:29
Frequency

It seems that calibration for 20 mA current signal input is not correct.Use the calibration parameters "126" and "C7" to calibrate the inverter.Perform calib... More Details >>
- No：21785
- Release Date：2018/08/22 16:29
Setting frequency

Set Pr.52 (DU/PU main display data selection) to "5".This allows for displaying the setting frequency on the voltage monitor.Then, switch to the monitor mode... More Details >>
- No：21784
- Release Date：2018/08/22 16:29
Frequency setting

Pr.1 (Maximum frequency) and Pr.18 (Maximum frequency).　　 More Details >>
- No：21744
- Release Date：2018/08/22 16:29
Parameter setting

Set Pr.125 (Terminal 2 frequency setting gain frequency) to "50 Hz".Set Pr.1 (Maximum frequency) to "50 Hz". More Details >>
- No：21720
- Release Date：2018/08/22 16:29

111-120 of Total 294

Inquiries

page top