You cannot calibrate the frequency around the middle of the current input range.The inverter determines the top and bott

Setting Pr.73 to "0" does not generate 10 VDC output.The inverter itself only has 5 V at the terminal 10.Setting this pa

Yes, you can set all of the three relay contacts to fault contacts.Set Pr.320 (RA1 output selection), 321 (RA2 output se

Adjust the terminal 2 bias with Pr.C2 and Pr.C3, and the terminal 2 gain with Pr.125 and Pr.C4. Set Pr.C2 (Terminal 2 fr

When using multiple motors, connect an external thermal for each of them. Set Pr.9 to "0" to disable the function. (When

If "HOLD" is displayed, the key lock mode enabled. Press the "MODE" key for two seconds. Then, change the setting of Pr.

It is the standardized Mini-B connector.

Assign X16 signal, and set Pr.79 to "0", to switch the operation mode with turning ON/OFF X16 signal.

It is Pr.125 (Terminal 2 frequency setting gain frequency). Adjust the slope with C4 (903) (Terminal 2 frequency setting

Turn ON and OFF the RES signal to enable the inverter-driven operation.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-F700P

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-F700P ]

181-190 of Total 294

prev 19 / 30page next

Frequency setting

You cannot calibrate the frequency around the middle of the current input range.The inverter determines the top and bottom points in the bias/gain adjustment... More Details >>
- No：21736
- Release Date：2018/08/22 16:29
10 VDC voltage from terminal 10

Setting Pr.73 to "0" does not generate 10 VDC output.The inverter itself only has 5 V at the terminal 10.Setting this parameter to "0" allows 10 V input betw... More Details >>
- No：21727
- Release Date：2018/08/22 16:29
FR-A7AR E kit (Relay output function)

Yes, you can set all of the three relay contacts to fault contacts.Set Pr.320 (RA1 output selection), 321 (RA2 output selection), and 322 (RA3 output selecti... More Details >>
- No：21712
- Release Date：2018/08/22 16:29
Frequency setting

Adjust the terminal 2 bias with Pr.C2 and Pr.C3, and the terminal 2 gain with Pr.125 and Pr.C4. Set Pr.C2 (Terminal 2 frequency setting bias frequency) to 20... More Details >>
- No：21685
- Release Date：2018/08/22 16:28
Electronic thermal O/L relay setting

When using multiple motors, connect an external thermal for each of them. Set Pr.9 to "0" to disable the function. (When multiple motors are present, it is n... More Details >>
- No：21676
- Release Date：2018/08/22 16:28
Easy setting mode

If "HOLD" is displayed, the key lock mode enabled. Press the "MODE" key for two seconds. Then, change the setting of Pr.79 to "1". More Details >>
- No：21350
- Release Date：2018/08/22 16:27
Connection cable of FR-Configurator

It is the standardized Mini-B connector. More Details >>
- No：21312
- Release Date：2018/08/22 16:26
Switching between External operation mode and PU operation mode

Assign X16 signal, and set Pr.79 to "0", to switch the operation mode with turning ON/OFF X16 signal. More Details >>
- No：21288
- Release Date：2018/08/22 16:26
Replacement

It is Pr.125 (Terminal 2 frequency setting gain frequency). Adjust the slope with C4 (903) (Terminal 2 frequency setting gain) as necessary. More Details >>
- No：21247
- Release Date：2018/08/22 16:26
Electronic bypass function

Turn ON and OFF the RES signal to enable the inverter-driven operation. More Details >>
- No：21190
- Release Date：2018/08/22 16:26

181-190 of Total 294

Inquiries

page top