No, we have no cable 50 cm long. The optional cables 1 m, 3 m, and 5 m long are available. (1 m: FR-CB201, 3 m: FR-CB203

Pr.1 (Maximum frequency) and Pr.18 (Maximum frequency).

After setting Pr.340 to "10", you need to power OFF then ON the inverter to make the new setting enabled because you are

Set Pr.55 (Frequency monitor reference) to "100 Hz".If the indication of the installed frequency meter does not match th

The FR-E700 is not supported by FR-SW2-SETUP-WJ. The FR-E700 series are supported by FR-SW3-SETUP-WJ. This software can

Select the inverter capacity so that the rated output current of inverter ? rated motor current × 1.1.

Check if the input side voltage is equally applied to all three phases. The S phase voltage may be low because the input

The forward rotation and reverse rotation are enabled by pressing the FWD/REV key on the operation panel.

Signals input from the terminal 4 are not enabled if the terminal AU is not ON. For an inverter without the terminal AU,

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-F700P

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-F700P ]

191-200 of Total 295

prev 20 / 30page next

FR-PA07

No, we have no cable 50 cm long. The optional cables 1 m, 3 m, and 5 m long are available. (1 m: FR-CB201, 3 m: FR-CB203, 5 m: FR-CB205) More Details >>
- No：21365
- Release Date：2018/08/22 16:27
Frequency setting

Pr.1 (Maximum frequency) and Pr.18 (Maximum frequency).　　 More Details >>
- No：21744
- Release Date：2018/08/22 16:29
NET mode

After setting Pr.340 to "10", you need to power OFF then ON the inverter to make the new setting enabled because you are setting the operation upon power-on.... More Details >>
- No：21759
- Release Date：2018/08/22 16:29
Parameter setting

Set Pr.55 (Frequency monitor reference) to "100 Hz".If the indication of the installed frequency meter does not match the running frequency, use the calibrat... More Details >>
- No：21768
- Release Date：2018/08/22 16:29
Speed command

Calibrate the terminal 2 bias. More Details >>
- No：21281
- Release Date：2018/08/22 16:26
Supported model for FR-Configurator

The FR-E700 is not supported by FR-SW2-SETUP-WJ. The FR-E700 series are supported by FR-SW3-SETUP-WJ. This software can be downloaded from the Mitsubishi Ele... More Details >>
- No：21314
- Release Date：2018/08/22 16:26
Capacity selection

Select the inverter capacity so that the rated output current of inverter ? rated motor current × 1.1. More Details >>
- No：21326
- Release Date：2018/08/22 16:27
Input phase loss

Check if the input side voltage is equally applied to all three phases. The S phase voltage may be low because the input current flows when the voltage of th... More Details >>
- No：21340
- Release Date：2018/08/22 16:27
FR-PA07

The forward rotation and reverse rotation are enabled by pressing the FWD/REV key on the operation panel. More Details >>
- No：21364
- Release Date：2018/08/22 16:27
Terminal

Signals input from the terminal 4 are not enabled if the terminal AU is not ON. For an inverter without the terminal AU, assign the AU function to an unused ... More Details >>
- No：21679
- Release Date：2018/08/22 16:28

191-200 of Total 295

Inquiries

page top