Operations cannot be enabled separately. You only can disable or enable all the operations.

After setting Pr.79 (Operation mode selection) to "2" and Pr.340 (Communication startup mode selection) to "10", reset t

Set Pr.79 (Operation mode) setting value to "0", "2", or "6", Pr.340 (Communication startup mode selection) other than t

This subroutine is to check the data link status and needs to be executed only once at the start of the program.

It is OK if stations are set as reserved.

The inverter outputs the peak voltage 300 to 400 VDC of the bus voltage not in a pure sine wave but a in a PWM waveform.

After setting Pr.340 to "10", you need to power OFF then ON the inverter to make the new setting enabled because you are

If you are using CC-Link just to monitor the inverter and using the analog signal and multi-speed setting to set the fre

Set Pr.338 (Operation command source) to "1" (external terminal).Set Pr.339 (Speed command source) to "0" (communication

When the torque is supposed as 100% at 60 Hz, the torque becomes 75 % at 80 Hz. (Under V/F control, the torque decreases

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-F700P

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-F700P ]

221-230 of Total 294

prev 23 / 30page next

FR-PA07

Operations cannot be enabled separately. You only can disable or enable all the operations. More Details >>
- No：21366
- Release Date：2018/08/22 16:27
CC-Link communication

After setting Pr.79 (Operation mode selection) to "2" and Pr.340 (Communication startup mode selection) to "10", reset the inverter (or power ON again) to st... More Details >>
- No：21256
- Release Date：2018/08/22 16:26
CC-Link

Set Pr.79 (Operation mode) setting value to "0", "2", or "6", Pr.340 (Communication startup mode selection) other than the setting value, Pr.542 (Station num... More Details >>
- No：21896
- Release Date：2018/08/22 16:29
Program command

This subroutine is to check the data link status and needs to be executed only once at the start of the program. More Details >>
- No：21767
- Release Date：2018/08/22 16:29
CC-Link

It is OK if stations are set as reserved. More Details >>
- No：21868
- Release Date：2018/08/22 16:29
Terminal indicator lamp

The inverter outputs the peak voltage 300 to 400 VDC of the bus voltage not in a pure sine wave but a in a PWM waveform. Check if the lamp to be connected ca... More Details >>
- No：21323
- Release Date：2018/08/22 16:27
NET mode

After setting Pr.340 to "10", you need to power OFF then ON the inverter to make the new setting enabled because you are setting the operation upon power-on.... More Details >>
- No：21759
- Release Date：2018/08/22 16:29
CC-Link

If you are using CC-Link just to monitor the inverter and using the analog signal and multi-speed setting to set the frequency, you need to input them extern... More Details >>
- No：21900
- Release Date：2018/08/22 16:29
Frequency setting

Set Pr.338 (Operation command source) to "1" (external terminal).Set Pr.339 (Speed command source) to "0" (communication).Check the setting of Pr.79 for oper... More Details >>
- No：21869
- Release Date：2018/08/22 16:29
Frequency

When the torque is supposed as 100% at 60 Hz, the torque becomes 75 % at 80 Hz. (Under V/F control, the torque decreases when the frequency exceeds 60 Hz bec... More Details >>
- No：21284
- Release Date：2018/08/22 16:26

221-230 of Total 294

Inquiries

page top