After setting Pr.340 to "10", you need to power OFF then ON the inverter to make the new setting enabled because you are

Set Pr.37 (Speed display) to the speed obtained when operating the machine at the frequency set with Pr.505 (Speed setti

The inverter outputs the peak voltage 300 to 400 VDC of the bus voltage not in a pure sine wave but a in a PWM waveform.

When the torque is supposed as 100% at 60 Hz, the torque becomes 75 % at 80 Hz. (Under V/F control, the torque decreases

Set Pr.79 (Operation mode) setting value to "0", "2", or "6", Pr.340 (Communication startup mode selection) other than t

Set the rotations per minute that is obtained while operating at the frequency set with Pr.505 (Speed setting reference)

The FR-DU04 can be used in the 700 series inverters, however, some restrictions apply and parameter copy is disabled.

No, it is not available. It is only available in the External operation mode or combined operation mode (PU speed comman

If you are using CC-Link just to monitor the inverter and using the analog signal and multi-speed setting to set the fre

No problem. The inverter actually occupies the reserved bits and does not use them.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-F700P

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-F700P ]

231-240 of Total 294

prev 24 / 30page next

NET mode

After setting Pr.340 to "10", you need to power OFF then ON the inverter to make the new setting enabled because you are setting the operation upon power-on.... More Details >>
- No：21759
- Release Date：2018/08/22 16:29
Monitor indicator

Set Pr.37 (Speed display) to the speed obtained when operating the machine at the frequency set with Pr.505 (Speed setting reference). (For FR-F700/E700/D700... More Details >>
- No：21716
- Release Date：2018/08/22 16:29
Terminal indicator lamp

The inverter outputs the peak voltage 300 to 400 VDC of the bus voltage not in a pure sine wave but a in a PWM waveform. Check if the lamp to be connected ca... More Details >>
- No：21323
- Release Date：2018/08/22 16:27
Frequency

When the torque is supposed as 100% at 60 Hz, the torque becomes 75 % at 80 Hz. (Under V/F control, the torque decreases when the frequency exceeds 60 Hz bec... More Details >>
- No：21284
- Release Date：2018/08/22 16:26
CC-Link

Set Pr.79 (Operation mode) setting value to "0", "2", or "6", Pr.340 (Communication startup mode selection) other than the setting value, Pr.542 (Station num... More Details >>
- No：21896
- Release Date：2018/08/22 16:29
Display unit of operation panel

Set the rotations per minute that is obtained while operating at the frequency set with Pr.505 (Speed setting reference) to Pr.37 (Speed display).For example... More Details >>
- No：21774
- Release Date：2018/08/22 16:29
Operation panel (DU04)

The FR-DU04 can be used in the 700 series inverters, however, some restrictions apply and parameter copy is disabled. More Details >>
- No：21261
- Release Date：2018/08/22 16:26
Electronic bypass function

No, it is not available. It is only available in the External operation mode or combined operation mode (PU speed command and External operation command (Pr.... More Details >>
- No：21192
- Release Date：2018/08/22 16:26
CC-Link

If you are using CC-Link just to monitor the inverter and using the analog signal and multi-speed setting to set the frequency, you need to input them extern... More Details >>
- No：21900
- Release Date：2018/08/22 16:29
CC-Link

No problem. The inverter actually occupies the reserved bits and does not use them. More Details >>
- No：21890
- Release Date：2018/08/22 16:29

231-240 of Total 294

Inquiries

page top