Set Pr.340 (Communication startup mode selection) to other than "0".Also, set Pr.79 (Operation mode) to "0", "2", or "6"

You can use it with the 700 series inverters. Note that the installation method of the card differs for the FR-E700 seri

When the torque is supposed as 100% at 60 Hz, the torque becomes 75 % at 80 Hz. (Under V/F control, the torque decreases

For low-speed operation, perform auto tuning and use (Advanced) magnetic flux vector control.

The multi-speed setting is prioritized.The external potentiometer setting is effective when the multi-speed signal is no

Yes.You can issue operation (forward/reverse), frequency setting, parameter read/write, and operation monitor commands.

You can select deceleration stop by setting Pr.502 (Stop mode selection at communication error). (Select from coasting t

When the pulse is counted and displayed, 1440 pulses are output with the frequency of the inverter is 60 Hz. Since these

Not available. Differences between the parts supplied with the FR-A7NC and FR-A7NC E kit will result in improper install

"n" in the address RWwn indicates a value determined by the station number setting.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-F700P

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-F700P ]

241-250 of Total 294

prev 25 / 30page next

CC-Link

Set Pr.340 (Communication startup mode selection) to other than "0".Also, set Pr.79 (Operation mode) to "0", "2", or "6".Powering the inverter on automatical... More Details >>
- No：21903
- Release Date：2018/08/22 16:30
CC-Link

You can use it with the 700 series inverters. Note that the installation method of the card differs for the FR-E700 series and FR-A700/F700 series.If you hav... More Details >>
- No：21887
- Release Date：2018/08/22 16:29
Frequency

When the torque is supposed as 100% at 60 Hz, the torque becomes 75 % at 80 Hz. (Under V/F control, the torque decreases when the frequency exceeds 60 Hz bec... More Details >>
- No：21284
- Release Date：2018/08/22 16:26
Magnetic flux vector control

For low-speed operation, perform auto tuning and use (Advanced) magnetic flux vector control. More Details >>
- No：21810
- Release Date：2018/08/22 16:29
Multi-speed setting and external potentiometer

The multi-speed setting is prioritized.The external potentiometer setting is effective when the multi-speed signal is not input. More Details >>
- No：21773
- Release Date：2018/08/22 16:29
CC-Link

Yes.You can issue operation (forward/reverse), frequency setting, parameter read/write, and operation monitor commands. More Details >>
- No：21899
- Release Date：2018/08/22 16:29
CC-Link

You can select deceleration stop by setting Pr.502 (Stop mode selection at communication error). (Select from coasting to stop, deceleration to stop, and con... More Details >>
- No：21892
- Release Date：2018/08/22 16:29
Pulse change

When the pulse is counted and displayed, 1440 pulses are output with the frequency of the inverter is 60 Hz. Since these pulses are limited to 2400 pulses, a... More Details >>
- No：21334
- Release Date：2018/08/22 16:27
FR-A7NC E kit

Not available. Differences between the parts supplied with the FR-A7NC and FR-A7NC E kit will result in improper installation. Use the FR-A7NC. Use the FR-A7NC. More Details >>
- No：21258
- Release Date：2018/08/22 16:26
CC-Link

"n" in the address RWwn indicates a value determined by the station number setting. More Details >>
- No：21867
- Release Date：2018/08/22 16:29

241-250 of Total 294

Inquiries

page top