Refer to the FR-A700/F700/E700/D700 series TECHNICAL MANUAL (section 3.7.2) and the Technical News. The FR-A700/F700/E70

Up to 42 units can be connected. (When only inverters are connected)

For low-speed operation, perform auto tuning and use (Advanced) magnetic flux vector control.

Set the rotations per minute that is obtained while operating at the frequency set with Pr.505 (Speed setting reference)

Connect the wire to the optional FR-A7NC's terminal block. (The terminal block is detachable.)

If Pr.340 (Communication startup mode selection) and Pr.79 (Operation mode selection) are set so that the inverter start

Use Pr.542 to set the station number and Pr.543 to set the baud rate.To set the baud rate to 10 Mbps, set Pr.543 to "4".

"n" in the address RWwn indicates a value determined by the station number setting.

The start commands cannot be input from both sources simultaneously because the operation command source is specified.Yo

Yes. Set the first monitor code in the lower 8 bits and the second monitor code in the upper 8 bits of RWwn.Set H6F to t

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-F700P

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-F700P ]

251-260 of Total 294

prev 26 / 30page next

Amount of heat generated

Refer to the FR-A700/F700/E700/D700 series TECHNICAL MANUAL (section 3.7.2) and the Technical News. The FR-A700/F700/E700/D700 series TECHNICAL MANUAL can be... More Details >>
- No：21263
- Release Date：2018/08/22 16:26
CC-Link

Up to 42 units can be connected. (When only inverters are connected) More Details >>
- No：21873
- Release Date：2018/08/22 16:29
Magnetic flux vector control

For low-speed operation, perform auto tuning and use (Advanced) magnetic flux vector control. More Details >>
- No：21810
- Release Date：2018/08/22 16:29
Display unit of operation panel

Set the rotations per minute that is obtained while operating at the frequency set with Pr.505 (Speed setting reference) to Pr.37 (Speed display).For example... More Details >>
- No：21774
- Release Date：2018/08/22 16:29
CC-Link

Connect the wire to the optional FR-A7NC's terminal block. (The terminal block is detachable.) More Details >>
- No：21875
- Release Date：2018/08/22 16:29
CC-Link

If Pr.340 (Communication startup mode selection) and Pr.79 (Operation mode selection) are set so that the inverter starts CC-Link operation from power-on and... More Details >>
- No：21840
- Release Date：2018/08/22 16:29
CC-Link

Use Pr.542 to set the station number and Pr.543 to set the baud rate.To set the baud rate to 10 Mbps, set Pr.543 to "4". More Details >>
- No：21839
- Release Date：2018/08/22 16:29
CC-Link

"n" in the address RWwn indicates a value determined by the station number setting. More Details >>
- No：21867
- Release Date：2018/08/22 16:29
CC-Link

The start commands cannot be input from both sources simultaneously because the operation command source is specified.You can switch the command source as ne... More Details >>
- No：21828
- Release Date：2018/08/22 16:29
CC-Link

Yes. Set the first monitor code in the lower 8 bits and the second monitor code in the upper 8 bits of RWwn.Set H6F to the first monitor code, and H70 to the... More Details >>
- No：21824
- Release Date：2018/08/22 16:29

251-260 of Total 294

Inquiries

page top