Set Pr.56 (Current monitor reference) to "10A".

Since the output frequency was measured, it is considered that the start signal was input correctly.Check the output vol

The detection level of the output current value cannot be changed using a potentiometer or a similar device.

Pr.1 (Maximum frequency) and Pr.18 (Maximum frequency).

Yes.Set Pr.19 (Base frequency voltage) to "200 V".200 V output will be obtained during 60 Hz operation.

You can monitor the fault output in both NET operation and external operation.

As described in the instruction manual, use the shielded cable or twisted cable to avoid the influence of noises.

Yes. The carrier frequency can be decreased by the setting of Pr.72 (PWM frequency selection).

When FR Configurator (FR-SW3-SETUP-WJ) is saved as a file from the menu, the extension is "me3". The size of this fie wi

To set the motor to coasting state, the following methods are available: 1. Set Pr.250 (Stop selection) to "0" and turn

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-F700P

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-F700P ]

61-70 of Total 295

prev 7 / 30page next

Terminal FM

Set Pr.56 (Current monitor reference) to "10A". More Details >>
- No：21865
- Release Date：2018/08/22 16:29
Output voltage

Since the output frequency was measured, it is considered that the start signal was input correctly.Check the output voltage on the voltage monitor of the in... More Details >>
- No：21780
- Release Date：2018/08/22 16:29
Output current value

The detection level of the output current value cannot be changed using a potentiometer or a similar device.　　 More Details >>
- No：21779
- Release Date：2018/08/22 16:29
Frequency setting

Pr.1 (Maximum frequency) and Pr.18 (Maximum frequency).　　 More Details >>
- No：21744
- Release Date：2018/08/22 16:29
Motor specifications setting

Yes.Set Pr.19 (Base frequency voltage) to "200 V".200 V output will be obtained during 60 Hz operation. More Details >>
- No：21717
- Release Date：2018/08/22 16:29
Switching between external operation and NET operation

You can monitor the fault output in both NET operation and external operation. More Details >>
- No：21686
- Release Date：2018/08/22 16:28
Applied terminal

As described in the instruction manual, use the shielded cable or twisted cable to avoid the influence of noises. More Details >>
- No：21344
- Release Date：2018/08/22 16:27
Countermeasure against noises

Yes. The carrier frequency can be decreased by the setting of Pr.72 (PWM frequency selection). More Details >>
- No：21338
- Release Date：2018/08/22 16:27
Saving parameter with FR-Configurator

When FR Configurator (FR-SW3-SETUP-WJ) is saved as a file from the menu, the extension is "me3". The size of this fie will be large since device settings and... More Details >>
- No：21311
- Release Date：2018/08/22 16:26
Motor coasting

To set the motor to coasting state, the following methods are available: 1. Set Pr.250 (Stop selection) to "0" and turn OFF the start command. 2. Short the t... More Details >>
- No：21271
- Release Date：2018/08/22 16:26

61-70 of Total 295

Inquiries

page top