Refer to the FR-A700/F700/E700/D700 series TECHNICAL MANUAL (section 3.7.2) and the Technical News. The FR-A700/F700/E70

The inverter outputs the peak voltage 300 to 400 VDC of the bus voltage not in a pure sine wave but a in a PWM waveform.

Specific settings are not required, however, when replacing the FR-E500, check that Pr.146 (Built-in potentiometer switc

No, we have no cable 50 cm long. The optional cables 1 m, 3 m, and 5 m long are available. (1 m: FR-CB201, 3 m: FR-CB203

The first priority window of the monitor may be set to the current.When the current is displayed on the monitor (the uni

Considering voltage drop of the internal power supply and influence by noise, the wiring length should be 30 m or less.

Check the setting of Pr.1 (Maximum frequency) and Pr.18 (High speed maximum frequency).Pr.1 is initially set to "120 Hz"

When the frequency is set using the setting dial, it is not necessary to set it again.The inverter memorizes the setting

This is due to specifications that multi-speed selection is prioritized and setting with the setting dial is ignored.The

The operation cannot be manually switched to the commercial power supply operation at an inverter fault. The operation c

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-F700P

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-F700P ]

81-90 of Total 295

prev 9 / 30page next

Amount of heat generated

Refer to the FR-A700/F700/E700/D700 series TECHNICAL MANUAL (section 3.7.2) and the Technical News. The FR-A700/F700/E700/D700 series TECHNICAL MANUAL can be... More Details >>
- No：21263
- Release Date：2018/08/22 16:26
Terminal indicator lamp

The inverter outputs the peak voltage 300 to 400 VDC of the bus voltage not in a pure sine wave but a in a PWM waveform. Check if the lamp to be connected ca... More Details >>
- No：21323
- Release Date：2018/08/22 16:27
FR-PA07

Specific settings are not required, however, when replacing the FR-E500, check that Pr.146 (Built-in potentiometer switchover) is not set to "0". If it is "0... More Details >>
- No：21363
- Release Date：2018/08/22 16:27
FR-PA07

No, we have no cable 50 cm long. The optional cables 1 m, 3 m, and 5 m long are available. (1 m: FR-CB201, 3 m: FR-CB203, 5 m: FR-CB205) More Details >>
- No：21365
- Release Date：2018/08/22 16:27
Monitor indicator

The first priority window of the monitor may be set to the current.When the current is displayed on the monitor (the unit is "A"), press "SET" to switch to t... More Details >>
- No：21765
- Release Date：2018/08/22 16:29
Frequency manual controller FR-AX

Considering voltage drop of the internal power supply and influence by noise, the wiring length should be 30 m or less. More Details >>
- No：21809
- Release Date：2018/08/22 16:29
Running frequency

Check the setting of Pr.1 (Maximum frequency) and Pr.18 (High speed maximum frequency).Pr.1 is initially set to "120 Hz". More Details >>
- No：21821
- Release Date：2018/08/22 16:29
Frequency setting

When the frequency is set using the setting dial, it is not necessary to set it again.The inverter memorizes the setting value internally even after the powe... More Details >>
- No：21842
- Release Date：2018/08/22 16:29
Frequency setting

This is due to specifications that multi-speed selection is prioritized and setting with the setting dial is ignored.The setting dial is effective when multi... More Details >>
- No：21843
- Release Date：2018/08/22 16:29
Electronic bypass function

The operation cannot be manually switched to the commercial power supply operation at an inverter fault. The operation can be automatically switched to the c... More Details >>
- No：21191
- Release Date：2018/08/22 16:26

81-90 of Total 295

Inquiries

page top