Yes, it does. When the inverter is coasting in the reverse direction, it starts in the reverse direction and switches to

It is not switched. The frequency at the fault saved in the faults history is always displayed in frequency [Hz].

As described in the instruction manual, use the shielded cable or twisted cable to avoid the influence of noises.

Specific settings are not required, however, when replacing the FR-E500, check that Pr.146 (Built-in potentiometer switc

Set Pr.125 (Terminal 2 frequency setting gain frequency) to "50 Hz".Set Pr.1 (Maximum frequency) to "50 Hz".

When turning the setting dial to set the frequency, press the "SET" key while the desired value blinks. (The setting fre

No parameter can be used to directly set this time.Changing Pr.9 (Electronic thermal O/L relay) changes the time.

To accept the current signal, the terminals AU (current input selection) and SD must be short-circuited. Check it.Note t

Check the setting of Pr.1 (Maximum frequency) and Pr.18 (High speed maximum frequency).Pr.1 is initially set to "120 Hz"

Change Pr.79 (Operation mode) to "3" (Combined operation mode) and short-circuit the external terminals STF and SD (or S

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-F700PJ

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-F700PJ ]

131-140 of Total 252

prev 14 / 26page next

Reverse rotation prevention selection

Yes, it does. When the inverter is coasting in the reverse direction, it starts in the reverse direction and switches to the forward rotation after a deceler... More Details >>
- No：21125
- Release Date：2018/08/22 16:26
Rotation speed display

It is not switched. The frequency at the fault saved in the faults history is always displayed in frequency [Hz]. More Details >>
- No：21180
- Release Date：2018/08/22 16:26
Applied terminal

As described in the instruction manual, use the shielded cable or twisted cable to avoid the influence of noises. More Details >>
- No：21344
- Release Date：2018/08/22 16:27
FR-PA07

Specific settings are not required, however, when replacing the FR-E500, check that Pr.146 (Built-in potentiometer switchover) is not set to "0". If it is "0... More Details >>
- No：21363
- Release Date：2018/08/22 16:27
Parameter setting

Set Pr.125 (Terminal 2 frequency setting gain frequency) to "50 Hz".Set Pr.1 (Maximum frequency) to "50 Hz". More Details >>
- No：21720
- Release Date：2018/08/22 16:29
Frequency setting

When turning the setting dial to set the frequency, press the "SET" key while the desired value blinks. (The setting frequency and "F" flicker alternately.) More Details >>
- No：21742
- Release Date：2018/08/22 16:29
Parameter

No parameter can be used to directly set this time.Changing Pr.9 (Electronic thermal O/L relay) changes the time. More Details >>
- No：21769
- Release Date：2018/08/22 16:29
Frequency setting

To accept the current signal, the terminals AU (current input selection) and SD must be short-circuited. Check it.Note that this terminal AU is not prepared ... More Details >>
- No：21799
- Release Date：2018/08/22 16:29
Running frequency

Check the setting of Pr.1 (Maximum frequency) and Pr.18 (High speed maximum frequency).Pr.1 is initially set to "120 Hz". More Details >>
- No：21821
- Release Date：2018/08/22 16:29
Parameter setting

Change Pr.79 (Operation mode) to "3" (Combined operation mode) and short-circuit the external terminals STF and SD (or STR and SD for reverse rotation). More Details >>
- No：21859
- Release Date：2018/08/22 16:29

131-140 of Total 252

Inquiries

page top