Yes. Use a moving-iron type ammeter. However, if the carrier frequency exceeds 5 kHz, do not use that meter since an ove

Calibrate C6 (Pr.904) (Terminal 4 frequency setting bias frequency) and C7 (Pr.905) (Terminal 4 frequency setting gain f

The FR-E700, D700, F700PJ may activate input phase loss protection "E.ILF" if the phase-to-phase voltage of the power su

You cannot use the setting dial while the terminals JOG and SD are turned ON.When performing JOG operation using externa

When turning the setting dial to set the frequency, press the "SET" key while the desired value blinks. (The setting fre

When using the setting dial to set the frequency, turn the dial and press the "SET" key while the desired value flickers

1. For MRS, coasting starts when the MRS contact turns ON. For Pr.250 = "0",IM is coasting immediately when the start si

Yes, it does. When the inverter is coasting in the reverse direction, it starts in the reverse direction and switches to

Even while the inverter is operating, you can use the setting dial to change the frequency and then press the SET key an

Auto tuning can be performed because the motor is one rank lower than the inverter capacity.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-F700PJ

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-F700PJ ]

11-20 of Total 252

prev 2 / 26page next

Connecting ammeter to output side

Yes. Use a moving-iron type ammeter. However, if the carrier frequency exceeds 5 kHz, do not use that meter since an overcurrent losses produced in the inter... More Details >>
- No：21681
- Release Date：2018/08/22 16:28
Frequency setting signal

Calibrate C6 (Pr.904) (Terminal 4 frequency setting bias frequency) and C7 (Pr.905) (Terminal 4 frequency setting gain frequency). If the situation does not ... More Details >>
- No：21265
- Release Date：2018/08/22 16:26
Input phase loss

The FR-E700, D700, F700PJ may activate input phase loss protection "E.ILF" if the phase-to-phase voltage of the power supply has become largely unbalanced. More Details >>
- No：21339
- Release Date：2018/08/22 16:27
RUN blinks

You cannot use the setting dial while the terminals JOG and SD are turned ON.When performing JOG operation using external signals, set Pr.79 (Operation mode)... More Details >>
- No：21823
- Release Date：2018/08/22 16:29
Frequency setting

When turning the setting dial to set the frequency, press the "SET" key while the desired value blinks. (The setting frequency and "F" flicker alternately.) More Details >>
- No：21742
- Release Date：2018/08/22 16:29
RUN blinks

When using the setting dial to set the frequency, turn the dial and press the "SET" key while the desired value flickers. (The value and "F" flicker alternat... More Details >>
- No：21692
- Release Date：2018/08/22 16:28
MRS setting

1. For MRS, coasting starts when the MRS contact turns ON. For Pr.250 = "0",IM is coasting immediately when the start signal is turned OFF. 　2. No. Set eithe... More Details >>
- No：21360
- Release Date：2018/08/22 16:27
Reverse rotation prevention selection

Yes, it does. When the inverter is coasting in the reverse direction, it starts in the reverse direction and switches to the forward rotation after a deceler... More Details >>
- No：21125
- Release Date：2018/08/22 16:26
Frequency setting

Even while the inverter is operating, you can use the setting dial to change the frequency and then press the SET key and the inverter operates at the new fr... More Details >>
- No：21739
- Release Date：2018/08/22 16:29
Offline auto tuning

Auto tuning can be performed because the motor is one rank lower than the inverter capacity. More Details >>
- No：21351
- Release Date：2018/08/22 16:27

11-20 of Total 252

Inquiries

page top