We do not offer a sample program for the programmable controller. Refer to the Instruction Manual and create the program

Yes. Set Pr.79 = 3. (Input the start signal from an external source.)

Yes. Set parameters as below.For FR-E500Set Pr.79 =3, and Pr.146= 0.Multi-speed is prioritized.For FR-S500Set Pr.79 = 3,

The RX7 output signal is the same as the signals for NO, NC, and transfer contact output.You can change the contents of

Installing the high power factor converter brings the power factor improving effect of 99% or higher.Therefore, when the

The output torque characteristics of the FREQROL-E500 series are shown in the figure below. Figure 1

When using one-rank-higher inverter, as you mention, you need to care about the setting of the electronic thermal O/L re

Already released.Unlike the E520, you need to purchase the optional card FR-E5NC.

General-purpose magnetic flux vector control is effective at low speed under a heavy load.To shorten the acceleration ti

It rotates in the forward direction while STF is ON.And then, when STR is turned ON and STF is turned OFF, the inverter

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-E500

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-E500 ]

11-20 of Total 85

prev 2 / 9page next

Do you have a sample program for 485 communication?

We do not offer a sample program for the programmable controller. Refer to the Instruction Manual and create the program by yourself. More Details >>
- No：21522
- Release Date：2018/08/22 16:28
Using built-in potentiometer and multi-speed together

Yes. Set Pr.79 = 3. (Input the start signal from an external source.) More Details >>
- No：21950
- Release Date：2018/08/22 16:30
Speed 2 operation with potentiometer on operation panel

Yes. Set parameters as below.For FR-E500Set Pr.79 =3, and Pr.146= 0.Multi-speed is prioritized.For FR-S500Set Pr.79 = 3, and Pr.53 = 1.Multi-speed is priorit... More Details >>
- No：21963
- Release Date：2018/08/22 16:30
Alarm output signal when using CC-Link

The RX7 output signal is the same as the signals for NO, NC, and transfer contact output.You can change the contents of this output signal using Pr.192.Pr.19... More Details >>
- No：22008
- Release Date：2018/08/22 16:30
Power factor improving effect by option

Installing the high power factor converter brings the power factor improving effect of 99% or higher.Therefore, when the high power factor converter is used,... More Details >>
- No：22020
- Release Date：2018/08/22 16:30
Relationship between frequency and output torque

The output torque characteristics of the FREQROL-E500 series are shown in the figure below. Figure 1 More Details >>
- No：22024
- Release Date：2018/08/22 16:30
Notes when inverter capacity is larger than motor capacity

When using one-rank-higher inverter, as you mention, you need to care about the setting of the electronic thermal O/L relay.Setting the electronic thermal O/... More Details >>
- No：22040
- Release Date：2018/08/22 16:30
CC-Link

Already released.Unlike the E520, you need to purchase the optional card FR-E5NC. More Details >>
- No：22050
- Release Date：2018/08/22 16:30
Parameter setting for FR-E500

General-purpose magnetic flux vector control is effective at low speed under a heavy load.To shorten the acceleration time, use Pr.44 to set the second accel... More Details >>
- No：22059
- Release Date：2018/08/22 16:30
Operation command terminal switching

It rotates in the forward direction while STF is ON.And then, when STR is turned ON and STF is turned OFF, the inverter decelerates down to 0 Hz within the s... More Details >>
- No：22070
- Release Date：2018/08/22 16:30

11-20 of Total 85

Inquiries

page top