Although you specify the FR-V200 and others as the inverter models, CC-Link is currently supported by the FR-A500 and FR

It is recommended to turn OFF the start signals (STF and STR) when stopping the inverter.In this case, it is not probabl

1. The output frequency satisfies the "control specification/frequency precision" even when the power supply voltage cha

Yes. Set parameters as below.For FR-E500Set Pr.79 =3, and Pr.146= 0.Multi-speed is prioritized.For FR-S500Set Pr.79 = 3,

Since the inverter displayed "0.00" instead of an error when the inverter speed dropped to 0 Hz and stopped by holding t

General-purpose magnetic flux vector control is effective at low speed under a heavy load.To shorten the acceleration ti

We do not offer a sample program for the programmable controller. Refer to the Instruction Manual and create the program

- SU signal (up to frequency signal)This signal is output when the inverter output frequency reaches the set frequency (

1. When the inverter power supply is turned OFF, the inverter is disconnected from the CC-Link network. However, since t

1. Since you can monitor the output frequency independently, you do not need to switch monitoring by the monitor command

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-E500

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-E500 ]

21-30 of Total 85

prev 3 / 9page next

CC-Link

Although you specify the FR-V200 and others as the inverter models, CC-Link is currently supported by the FR-A500 and FR-E500. The FR-V200E does not support ... More Details >>
- No：21499
- Release Date：2018/08/22 16:27
Operation at external operation/stop

It is recommended to turn OFF the start signals (STF and STR) when stopping the inverter.In this case, it is not probable that the motor rotates due to a cal... More Details >>
- No：22102
- Release Date：2018/08/22 16:31
Speed change due to power supply voltage fluctuation

1. The output frequency satisfies the "control specification/frequency precision" even when the power supply voltage changes, but the output voltage cannot r... More Details >>
- No：22069
- Release Date：2018/08/22 16:30
Speed 2 operation with potentiometer on operation panel

Yes. Set parameters as below.For FR-E500Set Pr.79 =3, and Pr.146= 0.Multi-speed is prioritized.For FR-S500Set Pr.79 = 3, and Pr.53 = 1.Multi-speed is priorit... More Details >>
- No：21963
- Release Date：2018/08/22 16:30
Speed does not exceed 46 Hz

Since the inverter displayed "0.00" instead of an error when the inverter speed dropped to 0 Hz and stopped by holding the winding machine by hand, it is con... More Details >>
- No：21492
- Release Date：2018/08/22 16:27
Parameter setting for FR-E500

General-purpose magnetic flux vector control is effective at low speed under a heavy load.To shorten the acceleration time, use Pr.44 to set the second accel... More Details >>
- No：22059
- Release Date：2018/08/22 16:30
Do you have a sample program for 485 communication?

We do not offer a sample program for the programmable controller. Refer to the Instruction Manual and create the program by yourself. More Details >>
- No：21522
- Release Date：2018/08/22 16:28
Difference between SU (up to frequency) and FU (frequency detection)

- SU signal (up to frequency signal)This signal is output when the inverter output frequency reaches the set frequency (the frequency the inverter is require... More Details >>
- No：21436
- Release Date：2018/08/22 16:27
Countermeasures when input power supply is turned off upon equipment fault

1. When the inverter power supply is turned OFF, the inverter is disconnected from the CC-Link network. However, since the CC-Link master station has the aut... More Details >>
- No：21390
- Release Date：2018/08/22 16:27
CC-Link monitor and parameter setting

1. Since you can monitor the output frequency independently, you do not need to switch monitoring by the monitor commands. Assign the remote register RWr0 to... More Details >>
- No：21418
- Release Date：2018/08/22 16:27

21-30 of Total 85

Inquiries

page top