Yes, you can use the 10BASE-T cable (straight) with the E500.

It is recommended to turn OFF the start signals (STF and STR) when stopping the inverter.In this case, it is not probabl

1. To perform emergency stop, it is recommended to have the motor coast and stop it using a mechanical brake.In this cas

Square wave input is not recommended since it can cause failures (for example, damage the diode bridge).

The power cannot be supplied to the control power supply separately for the FR-A024/A044 and small type FR-E500. Therefo

Your suggested use is not recommended due to the following reasons: Output voltage of the 400 V inverter contains "micro

Ensure that the inverter is in the PU operation mode and stopped, change the following parameters: 1. Read Pr.923 (Built

1. Since you can monitor the output frequency independently, you do not need to switch monitoring by the monitor command

The potentiometer on the operation panel is initially calibrated so that the maximum indication is slightly over 60 Hz w

We have no sample program for RS485 communication. Since the communication method of the FR-SW0-SETUP uses a different p

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-E500

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-E500 ]

31-40 of Total 85

prev 4 / 9page next

Operation panel extension cable

Yes, you can use the 10BASE-T cable (straight) with the E500. More Details >>
- No：22085
- Release Date：2018/08/22 16:30
Operation at external operation/stop

It is recommended to turn OFF the start signals (STF and STR) when stopping the inverter.In this case, it is not probable that the motor rotates due to a cal... More Details >>
- No：22102
- Release Date：2018/08/22 16:31
Inverter general matters

1. To perform emergency stop, it is recommended to have the motor coast and stop it using a mechanical brake.In this case, the output stop (MRS) signal is in... More Details >>
- No：22103
- Release Date：2018/08/22 16:31
Inverter input power supply

Square wave input is not recommended since it can cause failures (for example, damage the diode bridge). More Details >>
- No：22106
- Release Date：2018/08/22 16:31
Countermeasure against the instantaneous power failure with the inverter

The power cannot be supplied to the control power supply separately for the FR-A024/A044 and small type FR-E500. Therefore, the UPS is not available. More Details >>
- No：21368
- Release Date：2018/08/22 16:27
Driving 200 V motor by 400 V inverter

Your suggested use is not recommended due to the following reasons: Output voltage of the 400 V inverter contains "micro surge". Usually this surge voltage i... More Details >>
- No：21403
- Release Date：2018/08/22 16:27
Frequency setting

Ensure that the inverter is in the PU operation mode and stopped, change the following parameters: 1. Read Pr.923 (Built-in frequency setting potentiometer g... More Details >>
- No：21416
- Release Date：2018/08/22 16:27
CC-Link monitor and parameter setting

1. Since you can monitor the output frequency independently, you do not need to switch monitoring by the monitor commands. Assign the remote register RWr0 to... More Details >>
- No：21418
- Release Date：2018/08/22 16:27
Indication of potentiometer on operation panel

The potentiometer on the operation panel is initially calibrated so that the maximum indication is slightly over 60 Hz with the potentiometer turned to the m... More Details >>
- No：21427
- Release Date：2018/08/22 16:27
Communication operation with FR-E500

We have no sample program for RS485 communication. Since the communication method of the FR-SW0-SETUP uses a different protocol from 485 communication and st... More Details >>
- No：21451
- Release Date：2018/08/22 16:27

31-40 of Total 85

Inquiries

page top