You can use the Hioki Memory HiCorder and clamp-on AC/DC high tester.You can observe the inverter's frequency in one of

Connecting the brake resistor allows for quick deceleration because the regenerative power is processed. (The brake torq

If you are using analog voltage commands, connect the voltage inputs to the FR-E500 and FR-Z200 in parallel to equalize

For setting the frequency, you cannot switch between the operation panel potentiometer and current input from an externa

Pr.168 indicates the inverter software version.Pr.169 indicates the inverter software subversion history. These two para

Possible causes are:1. The reset signal (RES) is ON. 2. The built-in CPU is not working properly due to contact faults o

The FR-E500 manufactured before May 1998 behaved as you mentioned, and the potentiometer becomes unavailable once you se

Since a large load is applied to the motor when the electromagnetic clutch turns on, overcurrent may occur if the load i

Yes, you can use the 10BASE-T cable (straight) with the E500.

The output torque characteristics of the FREQROL-E500 series are shown in the figure below. Figure 1

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-E500

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-E500 ]

41-50 of Total 85

prev 5 / 9page next

Inverter

You can use the Hioki Memory HiCorder and clamp-on AC/DC high tester.You can observe the inverter's frequency in one of the following two methods:1. Attach t... More Details >>
- No：22082
- Release Date：2018/08/22 16:30
Brake resistor

Connecting the brake resistor allows for quick deceleration because the regenerative power is processed. (The brake torque increases.)Therefore, when an exte... More Details >>
- No：22045
- Release Date：2018/08/22 16:30
I want to synchronize the Z200 and E500.

If you are using analog voltage commands, connect the voltage inputs to the FR-E500 and FR-Z200 in parallel to equalize inputs to both units and speeds are s... More Details >>
- No：21929
- Release Date：2018/08/22 16:30
Built-in potentiometer and current input switching control

For setting the frequency, you cannot switch between the operation panel potentiometer and current input from an external source.To switch between the extern... More Details >>
- No：21985
- Release Date：2018/08/22 16:30
Parameters not covered in manual are displayed

Pr.168 indicates the inverter software version.Pr.169 indicates the inverter software subversion history. These two parameters are only used by the manufactu... More Details >>
- No：21532
- Release Date：2018/08/22 16:28
"Err" is displayed when STF signal turns ON

Possible causes are:1. The reset signal (RES) is ON. 2. The built-in CPU is not working properly due to contact faults of the inverter parts. Check the exte... More Details >>
- No：21484
- Release Date：2018/08/22 16:27
FR-E520 operation mode (Pr.79) selection

The FR-E500 manufactured before May 1998 behaved as you mentioned, and the potentiometer becomes unavailable once you set the frequency on the operation pane... More Details >>
- No：21525
- Release Date：2018/08/22 16:28
Clutch connection of load

Since a large load is applied to the motor when the electromagnetic clutch turns on, overcurrent may occur if the load is heavy. To ensure that the rated cur... More Details >>
- No：21955
- Release Date：2018/08/22 16:30
Operation panel extension cable

Yes, you can use the 10BASE-T cable (straight) with the E500. More Details >>
- No：22085
- Release Date：2018/08/22 16:30
Relationship between frequency and output torque

The output torque characteristics of the FREQROL-E500 series are shown in the figure below. Figure 1 More Details >>
- No：22024
- Release Date：2018/08/22 16:30

41-50 of Total 85

Inquiries

page top