You can use the Hioki Memory HiCorder and clamp-on AC/DC high tester.You can observe the inverter's frequency in one of

1. If the start signal is present when the power and communication restore, the inverter starts operation. 2. Similarly

If you are using analog voltage commands, connect the voltage inputs to the FR-E500 and FR-Z200 in parallel to equalize

Your suggested use is not recommended due to the following reasons: Output voltage of the 400 V inverter contains "micro

The output torque characteristics of the FREQROL-E500 series are shown in the figure below. Figure 1

"PS" appears when the STOP key on the operation panel is pressed during external operation. It is considered that someon

The potentiometer on the operation panel is initially calibrated so that the maximum indication is slightly over 60 Hz w

We have no sample program for RS485 communication. Since the communication method of the FR-SW0-SETUP uses a different p

Select the high-duty brake resistor according to the inverter capacity.

It is recommended to turn OFF the start signals (STF and STR) when stopping the inverter.In this case, it is not probabl

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-E500

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-E500 ]

41-50 of Total 84

prev 5 / 9page next

Inverter

You can use the Hioki Memory HiCorder and clamp-on AC/DC high tester.You can observe the inverter's frequency in one of the following two methods:1. Attach t... More Details >>
- No：22082
- Release Date：2018/08/22 16:30
Instantaneous power failure of facilities

1. If the start signal is present when the power and communication restore, the inverter starts operation. 2. Similarly to the above, if the start signal is ... More Details >>
- No：22093
- Release Date：2018/08/22 16:30
I want to synchronize the Z200 and E500.

If you are using analog voltage commands, connect the voltage inputs to the FR-E500 and FR-Z200 in parallel to equalize inputs to both units and speeds are s... More Details >>
- No：21929
- Release Date：2018/08/22 16:30
Driving 200 V motor by 400 V inverter

Your suggested use is not recommended due to the following reasons: Output voltage of the 400 V inverter contains "micro surge". Usually this surge voltage i... More Details >>
- No：21403
- Release Date：2018/08/22 16:27
Relationship between frequency and output torque

The output torque characteristics of the FREQROL-E500 series are shown in the figure below. Figure 1 More Details >>
- No：22024
- Release Date：2018/08/22 16:30
Indication of FR-E520

"PS" appears when the STOP key on the operation panel is pressed during external operation. It is considered that someone pressed the key. Dismiss "PS" in on... More Details >>
- No：21478
- Release Date：2018/08/22 16:27
Indication of potentiometer on operation panel

The potentiometer on the operation panel is initially calibrated so that the maximum indication is slightly over 60 Hz with the potentiometer turned to the m... More Details >>
- No：21427
- Release Date：2018/08/22 16:27
Communication operation with FR-E500

We have no sample program for RS485 communication. Since the communication method of the FR-SW0-SETUP uses a different protocol from 485 communication and st... More Details >>
- No：21451
- Release Date：2018/08/22 16:27
Selection of high-duty brake resistor

Select the high-duty brake resistor according to the inverter capacity. More Details >>
- No：21953
- Release Date：2018/08/22 16:30
Operation at external operation/stop

It is recommended to turn OFF the start signals (STF and STR) when stopping the inverter.In this case, it is not probable that the motor rotates due to a cal... More Details >>
- No：22102
- Release Date：2018/08/22 16:31

41-50 of Total 84

Inquiries

page top