Torque is limited by the lower set value of "[Pr.17] Torque limit setting value" and "[Cd.22] New torque value".When the

Check the following signals. • Start accept flag (M2001 to M2032) • Positioning start complete signal (M4000+20n (n: A

Error 2035 (Command frequency error) occurs when the servo amplifier detects a command frequency error. (1) When the com

There are two ways to start a positioning operation: (1) Set the "[Cd.3] Positioning start No.", and turn ON the positio

Alarm 2149 (Main circuit OFF warning) occurs when the servo system turns ON with no power supplied to the servo main cir

Check if 24 VDC power is supplied to "1A7" (pin No.) of the external input signal connector.

Error 3012 occurs when the multiple CPU setting of PLC CPU (CPU No.1) does not match that of Motion CPU. (1) Check if th

Minor error 120 occurs in the following case:The zero pass signal (M2406+20n) is OFF when the re-movement to the home po

Set "[PA04] Function selection A-1" to "_1_ _h: Invalid".(Note): When using Q17nCPUN, set "Servo amplifier parameter 23

The rapid stop deceleration time of parameter block is applied.However, when the rapid stop deceleration time is set in

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Motion Controllers > MELSEC-Q Series

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

MELSEC-Q Series

Positioning Modules(74)

QD75M(29)
QD75MH(33)
QD75H(1)
QD74MH(11)

FAQ within [ MELSEC-Q Series ]

11-20 of Total 59

prev 2 / 6page next

Torque limit

Torque is limited by the lower set value of "[Pr.17] Torque limit setting value" and "[Cd.22] New torque value".When the current torque reaches the limit, "b... More Details >>
- No：23592
- Release Date：2018/09/14 15:09
- Category： QD75M
Virtual servomotor

Check the following signals. • Start accept flag (M2001 to M2032) • Positioning start complete signal (M4000+20n (n: Axis No.-1)) More Details >>
- No：23552
- Release Date：2018/09/14 15:09
- Update：2023/02/08 10:39
- Category： Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Error 2035

Error 2035 (Command frequency error) occurs when the servo amplifier detects a command frequency error. (1) When the command is the permissible speed or high... More Details >>
- No：23577
- Release Date：2018/09/14 15:09
- Category： Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Positioning start

There are two ways to start a positioning operation: (1) Set the "[Cd.3] Positioning start No.", and turn ON the positioning start signal. (2) Use the dedica... More Details >>
- No：23593
- Release Date：2018/09/14 15:09
- Category： QD77MS , LD77MS , LD77MH , QD75MH , QD75M
Alarm 2149

Alarm 2149 (Main circuit OFF warning) occurs when the servo system turns ON with no power supplied to the servo main circuit. Review the condition of servo O... More Details >>
- No：23566
- Release Date：2018/09/14 15:09
- Category： Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Input/output signal

Check if 24 VDC power is supplied to "1A7" (pin No.) of the external input signal connector. More Details >>
- No：23594
- Release Date：2018/09/14 15:09
- Category： RD77MS , QD77MS , QD75MH , QD75M
Error 3012

Error 3012 occurs when the multiple CPU setting of PLC CPU (CPU No.1) does not match that of Motion CPU. (1) Check if the multiple CPU setting of the Multipl... More Details >>
- No：23563
- Release Date：2018/09/14 15:09
- Category： Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Minor error120

Minor error 120 occurs in the following case:The zero pass signal (M2406+20n) is OFF when the re-movement to the home position is performed by proximity dog,... More Details >>
- No：23559
- Release Date：2018/09/14 15:09
- Category： Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Servo amplifier forced stop

Set "[PA04] Function selection A-1" to "_1_ _h: Invalid".(Note): When using Q17nCPUN, set "Servo amplifier parameter 23 (Optional function 1)"... More Details >>
- No：23567
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Rapid stop signal

The rapid stop deceleration time of parameter block is applied.However, when the rapid stop deceleration time is set in the servo program, the value is enabl... More Details >>
- No：23557
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN

11-20 of Total 59

Inquiries

page top