Change the direction with "[PA14] Rotation direction selection/travel direction selection".

The following shows the setting value details.• 1 to 600: Positioning data No.• 7000 to 7004: Block start designation• 9

No, the speed limit cannot be changed during operation.

Because the rapid stop deceleration time is larger than the deceleration time.Set the rapid stop deceleration time withi

The following shows the initialization procedure. (1) Turn OFF the PLC ready flag. (2) Turn ON "[Cd.2] Parameter initia

No, the operation speed is not changed by changing the indirectly specified value.To change the speed during operation,

The rapid stop deceleration time of parameter block is applied.However, when the rapid stop deceleration time is set in

Set "[Pr.3] Movement amount per rotation" to "36000000(360.00000degree)", and "[Pr.4] Unit magnification" to "1".The sam

No, there is no impact on the command speed.However, the actual acceleration/deceleration time are affected by the chang

Torque is limited by the lower set value of "[Pr.17] Torque limit setting value" and "[Cd.22] New torque value/forward n

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Motion Controllers > MELSEC-Q Series

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

MELSEC-Q Series

Positioning Modules(74)

QD75M(29)
QD75MH(33)
QD75H(1)
QD74MH(11)

FAQ within [ MELSEC-Q Series ]

31-40 of Total 59

prev 4 / 6page next

Motor rotation direction

Change the direction with "[PA14] Rotation direction selection/travel direction selection". More Details >>
- No：23554
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU
Positioning start No.

The following shows the setting value details.• 1 to 600: Positioning data No.• 7000 to 7004: Block start designation• 9001: Machine home position return• 90... More Details >>
- No：23597
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Speed limit value change during operation

No, the speed limit cannot be changed during operation. More Details >>
- No：23571
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Deceleration stop

Because the rapid stop deceleration time is larger than the deceleration time.Set the rapid stop deceleration time within the range of 1 to the deceleration ... More Details >>
- No：23550
- Release Date：2018/09/14 15:09
- Category： Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU
Parameter initialization

The following shows the initialization procedure. (1) Turn OFF the PLC ready flag. (2) Turn ON "[Cd.2] Parameter initialization request". [QD75M, QD75MH, LD... More Details >>
- No：23602
- Release Date：2018/09/14 15:09
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Speed change

No, the operation speed is not changed by changing the indirectly specified value.To change the speed during operation, use CHGV instruction. More Details >>
- No：23555
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Rapid stop signal

The rapid stop deceleration time of parameter block is applied.However, when the rapid stop deceleration time is set in the servo program, the value is enabl... More Details >>
- No：23557
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Electronic gear

Set "[Pr.3] Movement amount per rotation" to "36000000(360.00000degree)", and "[Pr.4] Unit magnification" to "1".The same result is obtained by setting "3600... More Details >>
- No：23586
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Speed limit value

No, there is no impact on the command speed.However, the actual acceleration/deceleration time are affected by the change. More Details >>
- No：23595
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M , QD74MH
Torque limit

Torque is limited by the lower set value of "[Pr.17] Torque limit setting value" and "[Cd.22] New torque value/forward new torque value".When the current tor... More Details >>
- No：23591
- Release Date：2018/09/14 15:09
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD74MH

31-40 of Total 59

Inquiries

page top