To reflect the change, set "[PA14] Rotation direction selection/traveldirection selection" and cycle the servo amplifier

No, there is no impact on the command speed.However, the actual acceleration/deceleration time are affected by the chang

The following shows the initialization procedure. (1) Turn OFF the PLC ready flag. (2) Turn ON "[Cd.2] Parameter initia

Minor error 120 occurs in the following case:The zero pass signal (M2406+20n) is OFF when the re-movement to the home po

Refer to "b2: Command in-position flag" of "[Md.31] Status".

The following shows the procedure for changing the current value to a new value.(1) Write the new current value to "[Cd.

The rapid stop deceleration time of parameter block is applied.However, when the rapid stop deceleration time is set in

Error 2035 (Command frequency error) occurs when the servo amplifier detects a command frequency error. (1) When the com

Set "[Cd.16] Inching movement amount", and turn ON the Forward run JOG start signal or the Reverse run JOG start signal.

Yes. You can check the servo status through the following monitor data. • "[Md.108] Servo status 1" • "[Md.125] Servo st

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Motion Controllers > MELSEC-Q Series

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

MELSEC-Q Series

Positioning Modules(74)

QD75M(29)
QD75MH(33)
QD75H(1)
QD74MH(11)

FAQ within [ MELSEC-Q Series ]

31-40 of Total 59

prev 4 / 6page next

Servo motor rotation direction

To reflect the change, set "[PA14] Rotation direction selection/traveldirection selection" and cycle the servo amplifier or execute a home position return af... More Details >>
- No：23579
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Speed limit value

No, there is no impact on the command speed.However, the actual acceleration/deceleration time are affected by the change. More Details >>
- No：23556
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Parameter initialization

The following shows the initialization procedure. (1) Turn OFF the PLC ready flag. (2) Turn ON "[Cd.2] Parameter initialization request". [QD75M, QD75MH, LD... More Details >>
- No：23602
- Release Date：2018/09/14 15:09
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Minor error120

Minor error 120 occurs in the following case:The zero pass signal (M2406+20n) is OFF when the re-movement to the home position is performed by proximity dog,... More Details >>
- No：23559
- Release Date：2018/09/14 15:09
- Category： Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Command in-position

Refer to "b2: Command in-position flag" of "[Md.31] Status". More Details >>
- No：23598
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Current value change

The following shows the procedure for changing the current value to a new value.(1) Write the new current value to "[Cd. 9] New current value".(2) Write "900... More Details >>
- No：23585
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Rapid stop signal

The rapid stop deceleration time of parameter block is applied.However, when the rapid stop deceleration time is set in the servo program, the value is enabl... More Details >>
- No：23557
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Error 2035

Error 2035 (Command frequency error) occurs when the servo amplifier detects a command frequency error. (1) When the command is the permissible speed or high... More Details >>
- No：23577
- Release Date：2018/09/14 15:09
- Category： Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Inching operation

Set "[Cd.16] Inching movement amount", and turn ON the Forward run JOG start signal or the Reverse run JOG start signal. More Details >>
- No：23590
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Servo status

Yes. You can check the servo status through the following monitor data. • "[Md.108] Servo status 1" • "[Md.125] Servo status 3" (QD77MS, LD77MS, LD77MH) ... More Details >>
- No：23588
- Release Date：2018/09/14 15:09
- Update：2023/03/09 10:02
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M

31-40 of Total 59

Inquiries

page top