No, there is no impact on the command speed.However, the actual acceleration/deceleration time are affected by the chang

Minor error 120 occurs in the following case:The zero pass signal (M2406+20n) is OFF when the re-movement to the home po

It depends on the setting of servo parameter "[PA03] Absolute position detection system" whether the HPR request flag ("

Error 2035 (Command frequency error) occurs when the servo amplifier detects a command frequency error. (1) When the com

Check if 24 VDC power is supplied to "1A7" (pin No.) of the external input signal connector.

Error 2035 (Command frequency error) occurs when the servo amplifier detects a command frequency error. (1) When the com

Check the following signals. • Start accept flag (M2001 to M2032) • Positioning start complete signal (M4000+20n (n: Axi

Error 3012 occurs when the multiple CPU setting of PLC CPU (CPU No.1) does not match that of Motion CPU. (1) Check if th

The following shows the specification for the PLC CPU area. Q170MSCPU: Equivalent to PLC CPU "Q03UDCPU" • Pro

No, the time cannot be changed during operation. (Note): The following is the modules that support the acceleration/dec

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Motion Controllers > MELSEC-Q Series

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

MELSEC-Q Series

Positioning Modules(74)

QD75M(29)
QD75MH(33)
QD75H(1)
QD74MH(11)

FAQ within [ MELSEC-Q Series ]

41-50 of Total 59

prev 5 / 6page next

Speed limit value

No, there is no impact on the command speed.However, the actual acceleration/deceleration time are affected by the change. More Details >>
- No：23556
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Minor error120

Minor error 120 occurs in the following case:The zero pass signal (M2406+20n) is OFF when the re-movement to the home position is performed by proximity dog,... More Details >>
- No：23559
- Release Date：2018/09/14 15:09
- Category： Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
HPR request flag

It depends on the setting of servo parameter "[PA03] Absolute position detection system" whether the HPR request flag ("[Md.31] Status": b3) turns ON or not.... More Details >>
- No：23617
- Release Date：2018/09/14 15:09
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Error 2035

Error 2035 (Command frequency error) occurs when the servo amplifier detects a command frequency error. (1) When the command from the controller is the permi... More Details >>
- No：23616
- Release Date：2018/09/14 15:09
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M , QD74MH
Input/output signal

Check if 24 VDC power is supplied to "1A7" (pin No.) of the external input signal connector. More Details >>
- No：23594
- Release Date：2018/09/14 15:09
- Category： RD77MS , QD77MS , QD75MH , QD75M
Error 2035

Error 2035 (Command frequency error) occurs when the servo amplifier detects a command frequency error. (1) When the command is the permissible speed or high... More Details >>
- No：23577
- Release Date：2018/09/14 15:09
- Category： Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Virtual servomotor

Check the following signals. • Start accept flag (M2001 to M2032) • Positioning start complete signal (M4000+20n (n: Axis No.-1)) More Details >>
- No：23552
- Release Date：2018/09/14 15:09
- Update：2023/02/08 10:39
- Category： Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Error 3012

Error 3012 occurs when the multiple CPU setting of PLC CPU (CPU No.1) does not match that of Motion CPU. (1) Check if the multiple CPU setting of the Multipl... More Details >>
- No：23563
- Release Date：2018/09/14 15:09
- Category： Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
CUP type of stand-alone Motion controller

The following shows the specification for the PLC CPU area. Q170MSCPU: Equivalent to PLC CPU "Q03UDCPU" • Program capacity: 30k steps • LD instruction proces... More Details >>
- No：23578
- Release Date：2018/09/14 15:09
- Category： Q170MSCPU , Q170MCPU
Acceleration/deceleration time change

No, the time cannot be changed during operation. (Note): The following is the modules that support the acceleration/deceleration change function. • Q17nDSCP... More Details >>
- No：23570
- Release Date：2018/09/14 15:09
- Category： Q17nDCPU , Q170MCPU , Q17nHCPU , Q17nCPUN

41-50 of Total 59

Inquiries

page top