X and Y assignments are as follows.- X0 to XF- Y10 to Y1F

The fixed data is used for specific codes and character strings such as a command. Setting a device is not required.

The FX3U-ENET-L does not support the DHCP function. Set the fixed IP address using FX Configurator-EN-L. (FX Configurato

It is not possible to extend the length of the extension cable to over 65cm. Place the main unit separately by using the

No connector is provided with the module. Separately prepare any of the following connectors. A6CON1: Soldering type 32-

You can use "NZ2MC-1MBS", "NZ2MC-2MBS", "NZ2MC-4MBS", "NZ2MC-8MBS", "NZ2MC-16MBS",and "NZ2MC-8MBSE". You cannot use ext

Intelligent function module settings allow them to be set in both master and slave stations.

GX Developer does not need deleting when GX Works2 is installed.

This problem occurs because the consecutive free memory space for temporarily storing the program during online change i

Step ladders are not available in LCPU. There is no alternative function.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Programmable Controllers MELSEC

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(643)

CPU Module(179)
I/O Module(5)
Analog(16)
High-Speed Counter(14)
Motion/Positioning(11)
Network/Communication(97)
Option(9)
Engineering Software(61)
Safety Control(1)

Engineering Software(129)

FAQ within [ Programmable Controllers MELSEC ]

91-100 of Total 1010

prev 10 / 101page next

Assigning X and Y signals of AJ65SBTB1-32DT

X and Y assignments are as follows.- X0 to XF- Y10 to Y1F More Details >>
- No：23034
- Release Date：2018/09/03 17:31
- Category： Network related products
Unit of receive data used by the QJ71C24N series pre-defined protocol support function

The fixed data is used for specific codes and character strings such as a command. Setting a device is not required. More Details >>
- No：23049
- Release Date：2018/09/03 17:31
- Category： Network related products
Support of the DHCP (Dynamic Host Configuration Protocol) function by the FX3U-ENET-L (for Ethernet communications)

The FX3U-ENET-L does not support the DHCP function. Set the fixed IP address using FX Configurator-EN-L. (FX Configurator-EN-L can be downloaded from Mitsubi... More Details >>
- No：24869
- Release Date：2019/04/15 08:06
- Category： MELSEC-F Series
Extending the extension cable

It is not possible to extend the length of the extension cable to over 65cm. Place the main unit separately by using the parallel link or N:N Network functio... More Details >>
- No：24941
- Release Date：2019/04/18 14:25
- Category： MELSEC-F Series , Accessories
Accessories of the MELSEC iQ-R series 40-pin connector type module

No connector is provided with the module. Separately prepare any of the following connectors. A6CON1: Soldering type 32-point connector (40-pin connector) A6... More Details >>
- No：22467
- Release Date：2018/09/03 17:28
- Category： MELSEC iQ-R Series
Models of extended SRAM cassettes that can be used with MELSEC iQ-R series CPU modules

You can use "NZ2MC-1MBS", "NZ2MC-2MBS", "NZ2MC-4MBS", "NZ2MC-8MBS", "NZ2MC-16MBS",and "NZ2MC-8MBSE". You cannot use extended SRAM cassettes for the high-spe... More Details >>
- No：22468
- Release Date：2018/09/03 17:28
- Update：2018/09/21 16:36
- Category： MELSEC iQ-R Series
MODBUS(R) interface module's involvement in master and slave stations

Intelligent function module settings allow them to be set in both master and slave stations. More Details >>
- No：22637
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series
Deleting GX Developer when installing GX Works2

GX Developer does not need deleting when GX Works2 is installed. More Details >>
- No：22670
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series
When a message indicating that "the memory space is insufficient" appears during online change

This problem occurs because the consecutive free memory space for temporarily storing the program during online change is insufficient. In this case, perform... More Details >>
- No：22722
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series
Availability of step ladders for FX in L series

Step ladders are not available in LCPU. There is no alternative function. More Details >>
- No：22752
- Release Date：2018/09/03 17:29
- Category： MELSEC-L Series

91-100 of Total 1010

Inquiries

page top