Mitsubishi Electric shall accept product repairs for seven years after production of the product is discontinued. Howeve

Each special function unit/block has 8 occupied points, except for some special function devices. These 8 points do not

The FX3U-ENET-ADP does not support the DHCP function. Set the fixed IP address using the parameter setting of GX Works2.

The non-protocol communication can be set by the following two methods: (1) setting parameters using a programming tool,

The MODE switch can set the following modes.- 0 to 4: Online mode- 5 to 9: Line test mode- A to E: Hardware test modeEac

Short between SDA and RDA and between SDB and RDB, and then connect them to + (Data-A) and - (Data-B) on the external de

The default receive complete code is CR+LF (0DH, 0AH). The default received data count is 511 words. Hence, at their def

Set the size of buffer memory used for transient transmission (by dedicated instructions) to local stations, the standby

You can change the destination in [Online] -> [Specify Connection Destination]. Change the destination depending on t

For MX Component Ver.5, Ver. 5.000A or later supports the FX5U/FX5UC/FX5UJ CPU modules, and Ver. 5.003D or later support

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Programmable Controllers MELSEC

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(672)

CPU Module(185)
I/O Module(5)
Analog(16)
High-Speed Counter(14)
Motion/Positioning(11)
Network/Communication(106)
Option(9)
Engineering Software(62)
Safety Control(1)

Engineering Software(129)

FAQ within [ Programmable Controllers MELSEC ]

211-220 of Total 1023

prev 22 / 103page next

Repair term for the FX programmable controllers after discontinuation of production

Mitsubishi Electric shall accept product repairs for seven years after production of the product is discontinued. However, some products cannot be repaired d... More Details >>
- No：24996
- Release Date：2019/04/23 10:41
- Category： MELSEC-F Series , Main Unit , I/O Extension , Analog Control , High-Speed Counting , Positioning Control , Network/Communication , Accessories
Number of occupied points of special function devices

Each special function unit/block has 8 occupied points, except for some special function devices. These 8 points do not occupy 8 points of the actual I/O n... More Details >>
- No：24873
- Release Date：2019/04/15 08:06
- Category： MELSEC-F Series , Main Unit
Support of the DHCP (Dynamic Host Configuration Protocol) function by the FX3U-ENET-ADP (for Ethernet communications)

The FX3U-ENET-ADP does not support the DHCP function. Set the fixed IP address using the parameter setting of GX Works2. On GX Works2, select "Parameter" and... More Details >>
- No：24870
- Release Date：2019/04/15 08:05
- Category： MELSEC-F Series , Network/Communication
Communication setting methods when the FX3U-232-BD is used

The non-protocol communication can be set by the following two methods: (1) setting parameters using a programming tool, such as GX Works2, or (2) writing da... More Details >>
- No：24773
- Release Date：2019/02/27 15:24
- Category： MELSEC-F Series , Engineering Software , Network/Communication
MODE switch setting for QJ61BT11N

The MODE switch can set the following modes.- 0 to 4: Online mode- 5 to 9: Line test mode- A to E: Hardware test modeEach mode in ascending order of set valu... More Details >>
- No：23025
- Release Date：2018/09/03 17:31
- Category： Network related products
RS-485 connection between QJ71C24N and an external device

Short between SDA and RDA and between SDB and RDB, and then connect them to + (Data-A) and - (Data-B) on the external device. More Details >>
- No：22986
- Release Date：2018/09/03 17:31
- Category： Network related products
Reception data read request signal of QJ71C24N not turn ON

The default receive complete code is CR+LF (0DH, 0AH). The default received data count is 511 words. Hence, at their defaults, Reception data read request si... More Details >>
- No：22984
- Release Date：2018/09/03 17:31
- Update：2018/09/25 17:22
- Category： Network related products
Intelligent Buffer Select of the CC-Link parameter

Set the size of buffer memory used for transient transmission (by dedicated instructions) to local stations, the standby master station, and intelligent devi... More Details >>
- No：22977
- Release Date：2018/09/03 17:31
- Category： Network related products
How to change the specified connection destination of GX Works3

You can change the destination in [Online]-> [Specify Connection Destination]. Change the destination depending on the communication path to be used. Yo... More Details >>
- No：22472
- Release Date：2018/09/03 17:28
- Update：2018/09/19 14:31
- Category： MELSEC iQ-R Series
Regarding communication with MX Component

For MX Component Ver.5, Ver. 5.000A or later supports the FX5U/FX5UC/FX5UJ CPU modules, and Ver. 5.003D or later supports the FX5S CPU module. Also, both se... More Details >>
- No：22328
- Release Date：2018/08/30 13:55
- Update：2023/02/15 13:07
- Category： MELSEC iQ-F Series , CPU Module , Engineering Software , Network/Communication

211-220 of Total 1023

Inquiries

page top