For the first input extension block connecting to a main unit, use the FX2NC-100BPCB power supply cable provided with th

If the OUT instruction using the device number of the latch target device exists in a sequence program, the latched data

D8030 for VR1, and D8031 for VR2.

Checking "Device Memory" does not read file registers. Switch the Target Memory for "PLC Data" to "Standard RAM" and che

The bits 0 to F of the special register SD1286 (Receive state signal) correspond to the connection numbers 1 to 16. When

When an SET instruction and RST instruction use a single device, no duplicated coil error is detected.

All input COM terminals send the same signal because all the terminals are internally connected. To turn on the input,

You can use the SWAP (P) command to swap the upper and lower bytes of the specified device.

The "Forced ON/OFF function for external input/output" that forces X/Y devices to turn on/off from GX Works3 is supporte

In GX Works3, set the FX5-ENET module parameters from Basic Settings - External Device Configuration Settings. In the "

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Programmable Controllers MELSEC

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(672)

CPU Module(185)
I/O Module(5)
Analog(16)
High-Speed Counter(14)
Motion/Positioning(11)
Network/Communication(106)
Option(9)
Engineering Software(62)
Safety Control(1)

Engineering Software(129)

FAQ within [ Programmable Controllers MELSEC ]

271-280 of Total 1023

prev 28 / 103page next

Power supply cable of the input extension blocks for the connector type programmable controllers

Forthe first input extension block connecting to a main unit, use the FX2NC-100BPCB power supply cable provided with the main unit, and supply power from a 2... More Details >>
- No：24911
- Release Date：2019/04/15 11:32
- Category： MELSEC-F Series , Main Unit , I/O Extension
Data backup failure

If the OUT instruction using the device number of the latch target device exists in a sequence program, the latched data may be overwritten by execution of t... More Details >>
- No：24783
- Release Date：2019/02/27 16:16
- Category： MELSEC-F Series , Engineering Software , Main Unit
Built-in variable analog potentiometers of the FX3G series

D8030 for VR1, and D8031 for VR2. More Details >>
- No：24769
- Release Date：2019/02/27 15:01
- Category： MELSEC-F Series , Main Unit , Analog Control
Operation performed when file registers are read

Checking "Device Memory" does not read file registers. Switch the Target Memory for "PLC Data" to "Standard RAM" and check "File Register" in the Read from P... More Details >>
- No：22835
- Release Date：2018/09/03 17:30
- Category： Engineering Software
SD1286 of LCPU with built-in Ethernet port

The bits 0 to F of the special register SD1286 (Receive state signal) correspond to the connection numbers 1 to 16. When it receives data, the corresponding ... More Details >>
- No：22786
- Release Date：2018/09/03 17:30
- Category： MELSEC-L Series
Duplicated coil errors that can be checked with GX Works3

When an SET instruction and RST instruction use a single device, no duplicated coil error is detected. More Details >>
- No：22456
- Release Date：2018/09/03 17:28
- Update：2018/09/20 13:33
- Category： MELSEC iQ-R Series
Multiple input COM terminals

All input COM terminals send the same signal because all the terminals are internally connected. To turn on the input, the extension unit must be connected ... More Details >>
- No：22274
- Release Date：2018/08/30 13:48
- Category： MELSEC-F Series , Main Unit , I/O Extension
Regarding swapping upper and lower bytes of string data

You can use the SWAP (P) command to swap the upper and lower bytes of the specified device. More Details >>
- No：44361
- Release Date：2024/03/27 15:55
- Category： MELSEC iQ-F Series , CPU Module , Engineering Software
Regarding forced ON/OFF function for external input/output

The "Forced ON/OFF function for external input/output" that forces X/Y devices to turn on/off from GX Works3 is supported with the following firmware version... More Details >>
- No：44330
- Release Date：2024/03/20 12:56
- Category： MELSEC iQ-F Series , CPU Module
Regarding setting up encrypted communication (TLS) for FX5-ENET

In GX Works3, set the FX5-ENET module parameters from Basic Settings - External Device Configuration Settings. In the "Ethernet Configuration" screen, selec... More Details >>
- No：40050
- Release Date：2023/08/25 08:48
- Category： MELSEC iQ-F Series , Network/Communication

271-280 of Total 1023

Inquiries

page top