For issuance of a certificate, please consult your local Mitsubishi representative.

There are three types of configuration: GX Works3, special devices (SM/SD), and instructions. ・How to Configure in GX W

You can check the MAC address from the name plate on the side of the CPU module or by the Module diagnostics (CPU diagno

FX5U/FX5UC/FX5UJ CPU modules cannot perform firmware update using GX Works3. Use the SD memory card to update the firmwa

GX Works3 and the MELSEC iQ-R series do not use actual devices as automatic assignment devices of local labels. The loca

The "S/S" terminal is used to switch the input type (sink input and source input). For the source input, connect the "

Unless the necessity is described in manuals, a noise filter is not required. However, if the programmable controller i

File registers "R" use the block switching method. The number of file register points used are divided and specified in

It is necessary to set the latch range from the following GX Works3 parameters: [Navigation Window] -> [CPU Parameter

GX Developer Version 8.98C or later supports 64-bit Windows 7. To install GX Developer to a Windows 7-based personal com

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Programmable Controllers MELSEC

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(643)

CPU Module(179)
I/O Module(5)
Analog(16)
High-Speed Counter(14)
Motion/Positioning(11)
Network/Communication(97)
Option(9)
Engineering Software(61)
Safety Control(1)

Engineering Software(129)

FAQ within [ Programmable Controllers MELSEC ]

21-30 of Total 1010

prev 3 / 101page next

Certificate of non-applicability to export MELSEC-F to other countries

For issuance of a certificate, please consult your local Mitsubishi representative. More Details >>
- No：22264
- Release Date：2018/08/30 13:48
- Category： MELSEC-F Series , Main Unit , I/O Extension , Analog Control , High-Speed Counting , Positioning Control , Network/Communication , Accessories
Regarding FX5 CPU Module clock settings

There are three types of configuration: GX Works3, special devices (SM/SD), and instructions. ・How to Configure in GX Works3 　(1) In GX Works3, select On... More Details >>
- No：44365
- Release Date：2024/03/27 17:01
- Category： MELSEC iQ-F Series , CPU Module , Engineering Software
Regarding how to check MAC Addresses

You can check the MAC address from the name plate on the side of the CPU module or by the Module diagnostics (CPU diagnostics) of GX Works3. More Details >>
- No：39294
- Release Date：2023/02/13 15:37
- Category： MELSEC iQ-F Series , CPU Module , Network/Communication
Regarding how to update the firmware of the FX5 CPU module

FX5U/FX5UC/FX5UJ CPU modules cannot perform firmware update using GX Works3. Use the SD memory card to update the firmware. However, the FX5S CPU module sup... More Details >>
- No：39325
- Release Date：2023/02/14 09:03
- Category： MELSEC iQ-F Series , CPU Module , Engineering Software
How to check devices assigned to labels of GX Works3

GX Works3 and the MELSEC iQ-R series do not use actual devices as automatic assignment devices of local labels. The local labels use "label areas" in the "d... More Details >>
- No：22486
- Release Date：2018/09/03 17:28
- Update：2018/09/20 09:30
- Category： MELSEC iQ-R Series
How to use the "S/S" terminal

The "S/S" terminal is used to switch the input type (sink input and source input). For the source input, connect the "S/S" terminal to the "0V" terminal, a... More Details >>
- No：22255
- Release Date：2018/08/30 13:48
- Category： MELSEC-F Series , Main Unit , I/O Extension
Necessity for installing a noise filter

Unless the necessity is described in manuals, a noise filter is not required. However, if the programmable controller is used in an environment with much no... More Details >>
- No：22283
- Release Date：2018/08/30 13:48
- Category： MELSEC-F Series , Main Unit , I/O Extension , Analog Control , High-Speed Counting , Positioning Control , Network/Communication , Accessories
Difference between R and ZR

File registers "R" use the block switching method. The number of file register points used are divided and specified in units of 32k points. When multiple ... More Details >>
- No：22512
- Release Date：2018/09/03 17:28
- Update：2018/09/20 13:29
- Category： MELSEC-Q Series
Regarding the latch settings of data register

It is necessary to set the latch range from the following GX Works3 parameters: [Navigation Window] -> [CPU Parameters] -> [Device/Memory Settings] -&... More Details >>
- No：22329
- Release Date：2018/08/30 13:55
- Update：2024/11/11 13:49
- Category： CPU Module , Engineering Software
GX Developer's compatibility with 64-bit Windows 7

GX Developer Version 8.98C or later supports 64-bit Windows 7. To install GX Developer to a Windows 7-based personal computer, refer to the following techni... More Details >>
- No：22501
- Release Date：2018/09/03 17:28
- Update：2018/09/20 12:19
- Category： MELSEC-Q Series

21-30 of Total 1010

Inquiries

page top