- Set successive station numbers for the network modules in system A and system B in a redundant system. (Station n

FCN connectors (40-pin connector) are shown below.- A6CON1 (soldering connector)- A6CON2 (crimp connector)- A6CON3 (pres

The remote input RX of the master station and the remote input RX and remote output RY of local stations clear/hold the

Ethernet UTP cables cannot be used.

In the TCP/IP connection, you can connect up to 17 MELSOFT products at the same time using a dedicated connection for sy

No, you do not have to set the network range assignment parameters for slave stations. By setting the network range assi

There are no problems even though the SB/SW refresh device has not been set.

The following shows the major differences. - AJ65SBTB1-16TE - 1-wire terminal block, 1-common type - Maximum lo

For contacts to drive the coils of high-speed counters, use the contacts which are normally on during high-speed countin

The FX3U-2HSY-ADP, FX2N-10PG support differential line driver outputs.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Programmable Controllers MELSEC

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(578)

CPU Module(158)
I/O Module(5)
Analog(13)
High-Speed Counter(13)
Motion/Positioning(11)
Network/Communication(90)
Option(9)
Engineering Software(55)
Safety Control(1)

Engineering Software(129)

FAQ within [ Programmable Controllers MELSEC ]

351-360 of Total 983

prev 36 / 99page next

Precaution about MELSECNET/H connection (1)

- Set successive station numbers for the network modules in system A and system B in a redundant system. (Station number 0 cannot be set.) - Match "host... More Details >>
- No：23055
- Release Date：2018/09/03 17:31
- Update：2018/09/26 11:12
- Category： Network related products
Model name of the connector used for the FCN connector type CC-Link remote I/O module

FCN connectors (40-pin connector) are shown below.- A6CON1 (soldering connector)- A6CON2 (crimp connector)- A6CON3 (pressure-displacement connector)- A6CON4 ... More Details >>
- No：23056
- Release Date：2018/09/03 17:31
- Category： Network related products
Link data from communication error stations in a CC-Link network

The remote input RX of the master station and the remote input RX and remote output RY of local stations clear/hold the data from an error station according ... More Details >>
- No：23057
- Release Date：2018/09/03 17:31
- Category： Network related products
Using Ethernet UTP cables for the CC-Link IE Controller

Ethernet UTP cables cannot be used. More Details >>
- No：23062
- Release Date：2018/09/03 17:31
- Category： Network related products
Limitation on the number of MELSOFT products that can be connected with the QJ71E71

In the TCP/IP connection, you can connect up to 17 MELSOFT products at the same time using a dedicated connection for system and the connections for users 1 ... More Details >>
- No：23063
- Release Date：2018/09/03 17:31
- Category： Network related products
Parameter setting of CC-Link IE Field Network

No, you do not have to set the network range assignment parameters for slave stations. By setting the network range assignment parameters for a master statio... More Details >>
- No：23066
- Release Date：2018/09/03 17:31
- Category： Network related products
SB/SW refresh device setting with CC-Link

There are no problems even though the SB/SW refresh device has not been set. More Details >>
- No：23080
- Release Date：2018/09/03 17:31
- Category： Network related products
Differences between the AJ65SBTB1-16TE and AJ65SBTB1B-16TE1

The following shows the major differences. -AJ65SBTB1-16TE - 1-wire terminal block, 1-common type - Maximum load current: 0.1 A/point -Protection fu... More Details >>
- No：23083
- Release Date：2018/09/03 17:31
- Update：2018/09/26 13:16
- Category： Network related products
How to use built-in high-speed counters

For contacts to drive the coils of high-speed counters, use the contacts which are normally on during high-speed counting. Do not use the input (X000 to X00... More Details >>
- No：24684
- Release Date：2019/02/22 11:38
- Update：2019/02/22 15:03
- Category： MELSEC-F Series , High-Speed Counting
Modules that support differential line driver outputs

The FX3U-2HSY-ADP, FX2N-10PG support differential line driver outputs. More Details >>
- No：24691
- Release Date：2019/02/27 08:56
- Update：2023/02/15 13:09
- Category： MELSEC-F Series , Positioning Control

351-360 of Total 983

Inquiries

page top