The analog input type (temperature/voltage/current) and offset/gain can be set for each channel.

Turn off the drive contact of the WR3A instruction.

The following shows the major differences. - AJ65SBTB1-16TE - 1-wire terminal block, 1-common type - Maximum load c

The functional grounding is applied to ensure the reliability of the communication.

Use CC-Link dedicated cables. General-purpose cables cannot be used.

No, it is unnecessary. Terminating resistors are only required at both ends of the network.

To display a list of registers assigned to labels, check [Find Label Definition] and [Display all items] in the [Conditi

To send simultaneous broadcast using UDP, set the parameters as follows.- Destination IP Address: FF.FF.FF.FFh - Destina

The following settings are required for the "Open Setting" for the number of connected external devices. - Protocol: "U

Keep SM722 ON or correct the program so that any one of the ten numbers 0 to 9 is stored in each digit of the source dat

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Programmable Controllers MELSEC

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(672)

CPU Module(185)
I/O Module(5)
Analog(16)
High-Speed Counter(14)
Motion/Positioning(11)
Network/Communication(106)
Option(9)
Engineering Software(62)
Safety Control(1)

Engineering Software(129)

FAQ within [ Programmable Controllers MELSEC ]

391-400 of Total 1023

prev 40 / 103page next

Selection of analog inputs

The analog input type (temperature/voltage/current) and offset/gain can be set for each channel. More Details >>
- No：24902
- Release Date：2019/04/15 11:31
- Category： MELSEC-F Series , Analog Control
How to stop D/A conversion while the WR3A (Write to Dedicated Analog Block) instruction is being executed in the FX2N-2DA (analog output)

Turn off the drive contact of the WR3A instruction. More Details >>
- No：24872
- Release Date：2019/04/15 08:06
- Category： MELSEC-F Series , Analog Control
Differences between the AJ65SBTB1-16TE and AJ65SBTB1B-16TE1

The following shows the major differences. -AJ65SBTB1-16TE - 1-wire terminal block, 1-common type - Maximum load current: 0.1 A/point -Protection fu... More Details >>
- No：23083
- Release Date：2018/09/03 17:31
- Update：2018/09/26 13:16
- Category： Network related products
Grounding of CC-Link

The functional grounding is applied to ensure the reliability of the communication. More Details >>
- No：23076
- Release Date：2018/09/03 17:31
- Category： Network related products
Cables for CC-Link networks

Use CC-Link dedicated cables. General-purpose cables cannot be used. More Details >>
- No：23027
- Release Date：2018/09/03 17:31
- Category： Network related products
Necessity of terminating resistors in CC-Link communication

No, it is unnecessary. Terminating resistors are only required at both ends of the network. More Details >>
- No：22966
- Release Date：2018/09/03 17:31
- Category： Network related products
List of registers assigned to the labels set using GX Works2

To display a list of registers assigned to labels, check [Find Label Definition] and [Display all items] in the [Condition Setting] tab in the [Cross Refere... More Details >>
- No：22923
- Release Date：2018/09/03 17:30
- Update：2018/09/22 16:42
- Category： Engineering Software
Simultaneous broadcast transmission setting for built-in Ethernet port LCPU

To send simultaneous broadcast using UDP, set the parameters as follows.- Destination IP Address: FF.FF.FF.FFh - Destination Port Number: Other than FFFFh (S... More Details >>
- No：22785
- Release Date：2018/09/03 17:30
- Category： MELSEC-L Series
QCPU built-in Ethernet port setting when using the simple PLC communication function

The following settings are required for the "Open Setting" for the number of connected external devices. - Protocol: "UDP" - Open System: "MELSOFT connecti... More Details >>
- No：22654
- Release Date：2018/09/03 17:29
- Update：2018/09/21 12:02
- Category： MELSEC-Q Series
Operation error at the execution of a BIN instruction

Keep SM722 ON or correct the program so that any one of the ten numbers 0 to 9 is stored in each digit of the source data.An operation error occurs when data... More Details >>
- No：22635
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series

391-400 of Total 1023

Inquiries

page top