Set as follows in the Transfer Setup window. - Select "USB" for "PC side I/F". - Select "GOT" for "PLC side I/F" and se

Make settings of the built-in Ethernet port in the [Built-in Ethernet Port Setting] tab of the PLC parameter in GX Works

Totem pole output encoders cannot be connected to QD62.The following types of encoders can be connected.- Open collector

The QnUDE(H)CPU modules with serial numbers with upper 5 digits of "14112" or later indicate compatibility with the func

When GX Configurator-FL is used, programs for initial settings and cyclic data reading and writing are not needed.

Set "(Last five digits of actual device number) - 1" for the Target MODBUS(R) device head number.Example) For the holdin

Yes.You can also purchase MX Works, a set of MX Sheet and MX Component.

(1) If the A/D conversion enable signal is kept ON, conversion processing is kept performed. Once conversion proces

Maximum scan time (10 ms) + Response time (10 ms) = Pulse width with which the module recognizes all pulses (20 ms)

You can use the output change upper limit value and the MV upper/lower limit limiter, the functions common to each PID c

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Programmable Controllers MELSEC

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(672)

CPU Module(185)
I/O Module(5)
Analog(16)
High-Speed Counter(14)
Motion/Positioning(11)
Network/Communication(106)
Option(9)
Engineering Software(62)
Safety Control(1)

Engineering Software(129)

FAQ within [ Programmable Controllers MELSEC ]

481-490 of Total 1023

prev 49 / 103page next

Transparent function

Set as follows in the Transfer Setup window. - Select "USB" for "PC side I/F". - Select "GOT" for "PLC side I/F" and select "via GOT (direct coupled) tra... More Details >>
- No：22598
- Release Date：2018/09/03 17:29
- Update：2018/09/20 17:55
- Category： MELSEC-Q Series
Settings of the built-in Ethernet port of the universal model QCPU

Make settings of the built-in Ethernet port in the [Built-in Ethernet Port Setting] tab of the PLC parameter in GX Works2 or GX Developer. More Details >>
- No：22618
- Release Date：2018/09/03 17:29
- Update：2018/09/21 10:06
- Category： MELSEC-Q Series
Whether or not totem pole output type encoders are connected

Totem pole output encoders cannot be connected to QD62.The following types of encoders can be connected.- Open collector output type encoders- CMOS level vol... More Details >>
- No：22641
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series
Accessing file registers from the built-in Ethernet port QCPU using A-compatible 1E frames

The QnUDE(H)CPU modules with serial numbers with upper 5 digits of "14112" or later indicate compatibility with the function. The accessible device range is ... More Details >>
- No：22645
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series
Ladder programs for GX Configurator-FL

When GX Configurator-FL is used, programs for initial settings and cyclic data reading and writing are not needed. More Details >>
- No：22658
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series
Setting of "Target MODBUS(R) device head number"

Set "(Last five digits of actual device number) - 1" for the Target MODBUS(R) device head number.Example) For the holding register 400018, set "17". More Details >>
- No：22682
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series
Necessity for MX Component when MX Sheet is used

Yes.You can also purchase MX Works, a set of MX Sheet and MX Component. More Details >>
- No：22707
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series
Change timing of the status of A/D conversion module's I/O signals

(1)If the A/D conversion enable signal is kept ON, conversion processing is kept performed. Once conversion processing is successfully performed, A/D conve... More Details >>
- No：22710
- Release Date：2018/09/03 17:29
- Update：2018/09/21 15:12
- Category： MELSEC-Q Series
Pulse width with which the QX42 recognizes all pulses

Maximum scan time (10 ms) + Response time (10 ms) = Pulse width with which the module recognizes all pulses (20 ms) More Details >>
- No：22720
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series
How to control MV value

You can use the output change upper limit value and the MV upper/lower limit limiter, the functions common to each PID control tag. Set the following parame... More Details >>
- No：22724
- Release Date：2018/09/03 17:29
- Update：2018/09/26 16:40
- Category： MELSEC-Q Series

481-490 of Total 1023

Inquiries

page top