Products earlier than version 8.58L do not support a project in which the following parameters are set. All the paramete

GX Works2 Version 1.45X or later supports a print range specifying capability.Set "Start Step" and "End Step" for "Speci

Yes. They have the same pin layout.

The built-in I/O functions are standard functions of the L series CPU. Combining these functions flexibly achieves vario

Those switch settings are connected with each other. The switch setting of intelligent function module settings are easi

Basic arithmetic operations cannot be performed on unsigned words. Please assign the multiplier to a signed (single/doub

The serial communication modules do not require GX Configurator-SC. However, we recommend GX Configurator-SC as it reduc

I/O signals and buffer memory addresses need to be changed but data communications can be conducted using a FROM/TO inst

X devices will be assigned as follows. (With this setting, 32 points are occupied per station.) - Station No. 1: X100

For contacts to drive the coils of high-speed counters, use the contacts which are normally on during high-speed countin

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Programmable Controllers MELSEC

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(672)

CPU Module(185)
I/O Module(5)
Analog(16)
High-Speed Counter(14)
Motion/Positioning(11)
Network/Communication(106)
Option(9)
Engineering Software(62)
Safety Control(1)

Engineering Software(129)

FAQ within [ Programmable Controllers MELSEC ]

531-540 of Total 1023

prev 54 / 103page next

Opening a project in an old version of GX Developer

Products earlier than version 8.58L do not support a project in which the following parameters are set. All the parameters are set to their default values be... More Details >>
- No：22666
- Release Date：2018/09/03 17:29
- Update：2018/09/21 13:53
- Category： MELSEC-Q Series
Specifying steps in printing data displayed in the window in GX Works2

GX Works2 Version 1.45X or later supports a print range specifying capability.Set "Start Step" and "End Step" for "Specified Print Range" in the Print window. More Details >>
- No：22695
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series
FNC connector pin layout in L series I/O module and Q series I/O module

Yes. They have the same pin layout. More Details >>
- No：22774
- Release Date：2018/09/03 17:30
- Category： MELSEC-L Series
LCPU built-in I/O function

The built-in I/O functions are standard functions of the L series CPU. Combining these functions flexibly achieves various controls with lower cost, eliminat... More Details >>
- No：22806
- Release Date：2018/09/03 17:30
- Category： MELSEC-L Series
Switch settings of intelligent function module and I/O assignment settings (GX Works2)

Those switch settings are connected with each other. The switch setting of intelligent function module settings are easier to set. More Details >>
- No：22883
- Release Date：2018/09/03 17:30
- Category： Engineering Software
Multiplication in the Structured Text

Basic arithmetic operations cannot be performed on unsigned words. Please assign the multiplier to a signed (single/double) word. More Details >>
- No：22886
- Release Date：2018/09/03 17:30
- Category： Engineering Software
Necessity for GX Configurator-SC

The serial communication modules do not require GX Configurator-SC. However, we recommend GX Configurator-SC as it reduces man-hours. (1) The predefined ... More Details >>
- No：22905
- Release Date：2018/09/03 17:30
- Update：2018/09/22 16:33
- Category： Engineering Software
Using a FROM/TO instruction after AJ71UC24 is replaced with QJ71C24N

I/O signals and buffer memory addresses need to be changed but data communications can be conducted using a FROM/TO instruction and X/Y signals. More Details >>
- No：23017
- Release Date：2018/09/03 17:31
- Category： Network related products
Assignment for connecting two CC-Link remote input modules (16-point type) (Remote net Ver.1 mode)

X devices will be assigned as follows. (With this setting, 32 points are occupied per station.) - Station No. 1: X100 to X11F -Station No. 2: X120 to X13... More Details >>
- No：23082
- Release Date：2018/09/03 17:31
- Update：2018/09/26 13:15
- Category： Network related products
How to use built-in high-speed counters

For contacts to drive the coils of high-speed counters, use the contacts which are normally on during high-speed counting. Do not use the input (X000 to X00... More Details >>
- No：24684
- Release Date：2019/02/22 11:38
- Update：2019/02/22 15:03
- Category： MELSEC-F Series , High-Speed Counting

531-540 of Total 1023

Inquiries

page top