It's possible. Using special relays, it is possible to perform data logging from a program. For details, see the manual

In 8-bit mode, the upper 8 bits of transmitted and received data are ignored and only the lower 8 bits are valid data.

PLC :it is written to the CPU module and consumes the number of steps. ・Without character - 3 steps ・With character : 4

The following versions support the input interrupt delay function and can delay the start of execution. ・FX5U/FX5UC Ver.

In the iQ-F series, there is no lineup of display modules. Consider using web server function.

This function allows you to select the operation to be performed when the FX5-ENET(MQTT client) reconnects to the MQTT

The MQTT communication function of FX5-ENET does not allow multiple connections to be opened at the same time. The MQTT

PDO mapping is configured from the CC-Link IE TSN configuration settings. ① Open the CC-Link IE TSN configuration sett

Check whether the lamp is back to normal after disconnecting the wiring of the "24V" (service power supply) terminal. If

When an SET instruction and RST instruction use a single device, no duplicated coil error is detected.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Programmable Controllers MELSEC

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(643)

CPU Module(179)
I/O Module(5)
Analog(16)
High-Speed Counter(14)
Motion/Positioning(11)
Network/Communication(97)
Option(9)
Engineering Software(61)
Safety Control(1)

Engineering Software(129)

FAQ within [ Programmable Controllers MELSEC ]

541-550 of Total 1010

prev 55 / 101page next

Regarding performing Data Logging with Special Relays

It's possible. Using special relays, it is possible to perform data logging from a program. For details, see the manual below. MELSEC iQ-F FX5 User's Manu... More Details >>
- No：39327
- Release Date：2023/02/14 09:05
- Category： MELSEC iQ-F Series , CPU Module
Regarding differences between 8 bit and 16 bit modes for non-protocol communication

In 8-bit mode, the upper 8 bits of transmitted and received data are ignored and only the lower 8 bits are valid data. In 16 bit mode, send/receive data i... More Details >>
- No：39363
- Release Date：2023/02/15 13:04
- Category： MELSEC iQ-F Series , CPU Module , Network/Communication
Regarding Statement and Note Types

PLC :it is written to the CPU module and consumes the number of steps. ・Without character - 3 steps ・With character : 4 + (Number of characters + 2 + 14) /... More Details >>
- No：40023
- Release Date：2023/08/24 15:39
- Category： MELSEC iQ-F Series , CPU Module , Engineering Software
Regarding Input Interrupt Delay

The following versions support the input interrupt delay function and can delay the start of execution. ・FX5U/FX5UC Ver. 1.290 or later ・FX5UJ Ver. 1.050 o... More Details >>
- No：40037
- Release Date：2023/08/24 15:43
- Category： MELSEC iQ-F Series , CPU Module
Regarding Display Module Support

In the iQ-F series, there is no lineup of display modules. Consider usingweb server function. More Details >>
- No：40045
- Release Date：2023/08/24 15:53
- Update：2023/08/24 15:56
- Category： MELSEC iQ-F Series , CPU Module
Regarding the clean session function of MQTT communication function

This function allows you to select the operation to be performed when the FX5-ENET(MQTT client) reconnects to the MQTT broker after communication has been ... More Details >>
- No：40054
- Release Date：2023/08/25 09:02
- Category： MELSEC iQ-F Series , Network/Communication
Regarding multiple connections for the MQTT communication function

The MQTT communication function of FX5-ENET does not allow multiple connections to be opened at the same time. The MQTT communication function has a maximum ... More Details >>
- No：44358
- Release Date：2024/03/27 16:02
- Category： MELSEC iQ-F Series , Network/Communication
Regarding PDO Mapping Settings

PDO mapping is configured from the CC-Link IE TSN configuration settings. ① Open the CC-Link IE TSN configuration settings from the FX5-CCLGN-MS Basic Set... More Details >>
- No：44475
- Release Date：2024/07/02 19:07
- Category： MELSEC iQ-F Series , Network/Communication
The power supply lamp of a running programmable controller suddenly turned off or flashes

Check whether the lamp is back to normalafter disconnecting the wiring of the "24V" (service power supply) terminal. Ifthe lamp is back to normal,the servic... More Details >>
- No：22267
- Release Date：2018/08/30 13:48
- Update：2019/02/19 11:53
- Category： MELSEC-F Series , Main Unit
Duplicated coil errors that can be checked with GX Works3

When an SET instruction and RST instruction use a single device, no duplicated coil error is detected. More Details >>
- No：22456
- Release Date：2018/09/03 17:28
- Update：2018/09/20 13:33
- Category： MELSEC iQ-R Series

541-550 of Total 1010

Inquiries

page top