Data stored in the programmable controller can be saved to a CF card using a FX3U-CF-ADP CF card special adapter for the

Yes, they are independent common terminals.

The built-in CC-Link/LT setting differs. For the FX3UC-32MT-LT, the built-in CC-Link/LT setting is performed with the

Yes, it is possible. To set the programmable controller to RUN again, while the programmable controller is stopped, set

Only one GT1020/GT1030 series (5 V type) can be connected to the FX3G series. To connect two GOTs, select the GT1020/GT1

Yes, it is possible. Set a new value for the target address to the target address change value (BFM#54, #53) during the

When a flag contact is not programmed directly under the instruction to be checked, the flag may be turned off depending

The constant operation processing time can be achieved by using constant scan mode. Refer to the programming manual of t

Since they are octal, the number after X7 is X10 and after X77 is X100.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Programmable Controllers MELSEC

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(578)

CPU Module(158)
I/O Module(5)
Analog(13)
High-Speed Counter(13)
Motion/Positioning(11)
Network/Communication(90)
Option(9)
Engineering Software(55)
Safety Control(1)

Engineering Software(129)

FAQ within [ Programmable Controllers MELSEC ]

691-700 of Total 983

prev 70 / 99page next

Data collection with FX programmable controller

Data stored in the programmable controller can be saved to a CF card usinga FX3U-CF-ADP CF card special adapter for the FX3U/FX3UC series. More Details >>
- No：24936
- Release Date：2019/04/18 14:24
- Category： MELSEC-F Series , Main Unit , Accessories
File format that can be saved to a CF card in the FX3U-CF-ADP

CSV file can be saved. More Details >>
- No：24938
- Release Date：2019/04/18 14:24
- Category： MELSEC-F Series , Main Unit , Accessories
Terminal layout on the output side of the FX3U-16MR/ES

Yes, they are independent common terminals. More Details >>
- No：24955
- Release Date：2019/04/18 14:23
- Category： MELSEC-F Series , Main Unit
Differences between the FX3UC-32MT-LT and the FX3UC-32MT-LT2

The built-in CC-Link/LT setting differs. For the FX3UC-32MT-LT, the built-in CC-Link/LT setting is performed with the DIP switch. For the FX3UC-32MT-LT2, th... More Details >>
- No：24956
- Release Date：2019/04/18 14:28
- Category： MELSEC-F Series , Main Unit , Network/Communication
M8037 (forced STOP signal)

Yes, it is possible. To set the programmable controller to RUN again, while the programmable controller is stopped, set the built-in RUN/STOP switch as follo... More Details >>
- No：24965
- Release Date：2019/04/23 07:18
- Category： MELSEC-F Series , Main Unit
Connection of the FX3G series and the GT1020/GT1030 series (5 V type)

Only one GT1020/GT1030 series (5 V type) can be connected to the FX3G series. To connect two GOTs, select the GT1020/GT1030 series (24 V type). More Details >>
- No：24969
- Release Date：2019/04/23 07:19
- Category： MELSEC-F Series , Main Unit
Target address change during the positioning operation in the FX3U-1PG

Yes, it is possible. Set a new value for the target address to the target address change value (BFM#54, #53) during the positioning operation. 　　 * The targ... More Details >>
- No：24986
- Release Date：2019/04/23 07:22
- Category： MELSEC-F Series , Positioning Control
Instruction execution complete flag

When a flag contact is not programmed directly under the instruction to be checked, the flag may be turned off depending on the execution status of another i... More Details >>
- No：24988
- Release Date：2019/04/23 07:22
- Category： MELSEC-F Series , Main Unit
Operation processing time of the programmable controller

The constant operation processing time can be achieved by using constant scan mode. Refer to the programming manual of the programmable controller used. More Details >>
- No：24997
- Release Date：2019/04/23 10:38
- Category： MELSEC-F Series , Engineering Software , Main Unit
Input numbers of the FX programmable controllers

Since they are octal, the number after X7 is X10 and after X77 is X100. More Details >>
- No：25000
- Release Date：2019/04/23 10:39
- Category： MELSEC-F Series , Engineering Software , Main Unit

691-700 of Total 983

Inquiries

page top