It can be cleared with the scan time clear function. You can clear maximum and minimum scan time with GX Works3 Ver. 1.0

The FX5U CPU module has a lineup of up to 80 point. The following configuration is recommended when replacing the FX3U-1

Assign data registers (D) to Latch (1) or Latch (2) in the "Device Setting" window ([PLC Parameter] -> "Device Settin

Personal computers have different MAC addresses and an Ethernet module hold a MAC address. Hence the MAC address that th

Modules do not need setting in GX Works2 if not selectable from "Module Selection" in the "New Module" window for intell

Input derating is the percentage of simultaneous ON points, one of the specifications applied when input modules are use

The clock setting of the CPU module is set automatically in accordance with the clock data collected from the time infor

The positioning operation starts just in 30 microseconds, with a maximum high speed output of 200k pulses per second. S-

The error code "2110" is "SP.UNIT ERROR.". This error may be caused by one of the following factors.(1) The module that

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Programmable Controllers MELSEC

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(672)

CPU Module(185)
I/O Module(5)
Analog(16)
High-Speed Counter(14)
Motion/Positioning(11)
Network/Communication(106)
Option(9)
Engineering Software(62)
Safety Control(1)

Engineering Software(129)

FAQ within [ Programmable Controllers MELSEC ]

721-730 of Total 1023

prev 73 / 103page next

Regarding clearing the maximum and minimum scan times

It can be cleared with the scan time clear function. You can clear maximum and minimum scan time with GX Works3 Ver. 1.085 P or later or by special relays. More Details >>
- No：39342
- Release Date：2023/02/15 10:05
- Category： MELSEC iQ-F Series , CPU Module , Engineering Software
Regarding replacement from 128 point type of FX3U

The FX5U CPU module has a lineup of up to 80 point. The following configuration is recommended when replacing the FX3U-128MR/ES. Recommended alternative (1... More Details >>
- No：44617
- Release Date：2024/11/28 16:13
- Category： MELSEC iQ-F Series , CPU Module
Setting of Q series registers whose data is held when a power failure occurs

Assign data registers (D) to Latch (1) or Latch (2) in the "Device Setting" window ([PLC Parameter] -> "Device Setting" window) to hold the data when a po... More Details >>
- No：22601
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series
Ethernet communication after the replacement of an external device

Personal computers have different MAC addresses and an Ethernet module hold a MAC address. Hence the MAC address that the Ethernet module currently holds is ... More Details >>
- No：22665
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series
Intelligent function module settings in GX Works2

Modules do not need setting in GX Works2 if not selectable from "Module Selection" in the "New Module" window for intelligent function module settings. More Details >>
- No：22685
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series
Input derating

Input derating is the percentage of simultaneous ON points, one of the specifications applied when input modules are used. When QX42 is used in a temperatur... More Details >>
- No：22692
- Release Date：2018/09/03 17:29
- Update：2018/10/03 16:23
- Category： MELSEC-Q Series
CPU clock setting by SNTP functions via built-in Ethernet port in LCPU

The clock setting of the CPU module is set automatically in accordance with the clock data collected from the time information server (SNTP server) on the LAN. More Details >>
- No：22736
- Release Date：2018/09/03 17:29
- Category： MELSEC-L Series
Built-in positioning function of LCPU

The positioning operation starts just in 30 microseconds, with a maximum high speed output of 200k pulses per second. S-curve acceleration/deceleration is al... More Details >>
- No：22790
- Release Date：2018/09/03 17:30
- Category： MELSEC-L Series
Error code "2110" in LCPU

The error code "2110" is "SP.UNIT ERROR.". This error may be caused by one of the following factors.(1) The module that has been specified by a FROM/TO instr... More Details >>
- No：22830
- Release Date：2018/09/03 17:30
- Category： MELSEC-L Series
MX Component Version 4's compatibility with 64-bit Windows 7

Yes. More Details >>
- No：22844
- Release Date：2018/09/03 17:30
- Category： Engineering Software

721-730 of Total 1023

Inquiries

page top