The MODE switch can set the following modes.- 0 to 4: Online mode- 5 to 9: Line test mode- A to E: Hardware test modeEac

Whether the positioning parameter is used or the extension positioning parameter is used can be selected in BFM#32 (posi

The longest gratis warranty term after manufacturing shall be eighteen (18) months. For details, refer to the gratis war

Whether the latch range is set by default is different. ・Latch (1) — Latch range is set by default. This can be changed

H3081 is caused by an analog ADP power failure and the analog ADP is not receiving power normally. The FX5-4A-ADP and FX

The boot operation function is configured and executed from the GX Works3 parameter settings as follows. (1) Open the bo

If cross-references are displayed on GX Works3, you can print them.

To update to firmware version “1.100 ” or higher, you need a product with serial number (S/N) or higher listed below. ・F

GX Developer/GX Works2 cannot be used. MELSEC iQ-F series only supports GX Works3.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Programmable Controllers MELSEC

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(672)

CPU Module(185)
I/O Module(5)
Analog(16)
High-Speed Counter(14)
Motion/Positioning(11)
Network/Communication(106)
Option(9)
Engineering Software(62)
Safety Control(1)

Engineering Software(129)

FAQ within [ Programmable Controllers MELSEC ]

781-790 of Total 1023

prev 79 / 103page next

MODE switch setting for QJ61BT11N

The MODE switch can set the following modes.- 0 to 4: Online mode- 5 to 9: Line test mode- A to E: Hardware test modeEach mode in ascending order of set valu... More Details >>
- No：23025
- Release Date：2018/09/03 17:31
- Category： Network related products
Parameter setting of FX3U-1PG

Whether the positioning parameter is used or the extension positioning parameter is used can be selected in BFM#32 (positioning parameter selection). Select ... More Details >>
- No：24917
- Release Date：2019/04/17 11:40
- Category： MELSEC-F Series , Positioning Control
Gratis warranty term of the FX programmable controllers

The longest gratis warranty term after manufacturing shall be eighteen (18) months. For details, refer to the gratis warranty term explained in the applicabl... More Details >>
- No：24928
- Release Date：2019/04/17 11:42
- Category： MELSEC-F Series , Main Unit
Regarding the line tracing function

It is not supported. More Details >>
- No：39323
- Release Date：2023/02/14 09:01
- Category： MELSEC iQ-F Series , CPU Module , Engineering Software
Regarding the differences between Latches (1) and (2)

Whether the latch range is set by default is different. ・Latch (1) — Latch range is set by default. This can be changed at any time. ・Latch (2) — No latch ... More Details >>
- No：39351
- Release Date：2023/02/15 13:08
- Update：2024/08/19 09:54
- Category： MELSEC iQ-F Series , CPU Module , Engineering Software
Regarding analog ADP Power Supply abnormalities

H3081 is caused by an analog ADP power failure and the analog ADP is not receiving power normally. The FX5-4A-ADP and FX5-4DA-ADP are adapters that require p... More Details >>
- No：44346
- Release Date：2024/03/27 15:27
- Category： MELSEC iQ-F Series , Analog
Regarding Boot Operation procedures

The boot operation function is configured and executed from the GX Works3 parameter settings as follows. (1) Open the boot configuration screen. 　 From the... More Details >>
- No：44348
- Release Date：2024/03/27 15:29
- Category： MELSEC iQ-F Series , CPU Module
Regarding printing of cross-references

If cross-references are displayed on GX Works3, you can print them. More Details >>
- No：44619
- Release Date：2024/11/28 16:10
- Category： MELSEC iQ-F Series , CPU Module , Engineering Software
Regarding updating the FX5U/FX5UC CPU module to firmware version “1.100 ” or later

To update to firmware version “1.100 ” or higher, you need a product with serial number (S/N) or higher listed below. ・FX5UC-32MT/DS-TS and FX5UC-32MT/DSS-T... More Details >>
- No：44623
- Release Date：2024/11/28 16:14
- Category： MELSEC iQ-F Series , CPU Module
Regarding the compatible programming tool

GX Developer/GX Works2 cannot be used. MELSEC iQ-F series only supports GX Works3. More Details >>
- No：22292
- Release Date：2018/08/30 13:55
- Update：2023/06/23 10:34
- Category： MELSEC iQ-F Series , CPU Module , Engineering Software

781-790 of Total 1023

Inquiries

page top