While the module configuration window is being displayed, the I/O assignment can be checked by selecting the following o

N:N Network, Parallel Link, MC protocol, Non-protocol communication, MELSOFT connection, MODBUS RTU, and Predefined prot

When an SET instruction and RST instruction use a single device, no duplicated coil error is detected.

The LED can be turned OFF by operations from GX Developer. The operation method is as follows.(1) Connect to the CPU in

Assign data registers (D) to Latch (1) or Latch (2) in the "Device Setting" window ([PLC Parameter] -> "Device Settin

In the "Reference/Reflection Target for Device Comment" window, switch the "Specify the Reference/Reflection" from "Glob

When an ACPU module is replaced with a QCPU module, programs for the ACPU module can be used by changing the PLC type in

Click the local label to be checked and select "Cross Reference" from the right-click menu to check the devices.

When a coil of the high-speed counter or an interrupt pointer is programmed, the programmable controller system adjusts

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Programmable Controllers MELSEC

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(672)

CPU Module(185)
I/O Module(5)
Analog(16)
High-Speed Counter(14)
Motion/Positioning(11)
Network/Communication(106)
Option(9)
Engineering Software(62)
Safety Control(1)

Engineering Software(129)

FAQ within [ Programmable Controllers MELSEC ]

791-800 of Total 1023

prev 80 / 103page next

Regarding I/O assignment on the module configuration diagram of GX Works3

While the module configuration window is being displayed, the I/O assignment can be checked by selecting the following options from the menu bar: [Edit]→[X... More Details >>
- No：22307
- Release Date：2018/08/30 13:55
- Update：2023/06/23 10:25
- Category： CPU Module , I/O Module , Engineering Software
Regarding communication supported by built-in RS-485 port

N:N Network, Parallel Link, MC protocol, Non-protocol communication, MELSOFT connection, MODBUS RTU, and Predefined protocol support are available. More Details >>
- No：22322
- Release Date：2018/08/30 13:55
- Update：2022/12/22 10:16
- Category： MELSEC iQ-F Series , CPU Module , Network/Communication
Duplicated coil errors that can be checked with GX Works3

When an SET instruction and RST instruction use a single device, no duplicated coil error is detected. More Details >>
- No：22456
- Release Date：2018/09/03 17:28
- Update：2018/09/20 13:33
- Category： MELSEC iQ-R Series
How to turn OFF the "COM.ERR" LED of the Ethernet module

The LED can be turned OFF by operations from GX Developer. The operation method is as follows.(1) Connect to the CPU in the standby system in Transfer Setup.... More Details >>
- No：22571
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series
Setting of Q series registers whose data is held when a power failure occurs

Assign data registers (D) to Latch (1) or Latch (2) in the "Device Setting" window ([PLC Parameter] -> "Device Setting" window) to hold the data when a po... More Details >>
- No：22601
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series
How to display local comments in GX Works2

In the "Reference/Reflection Target for Device Comment" window, switch the "Specify the Reference/Reflection" from "Global" to "Local". More Details >>
- No：22630
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series
Compatibility between the A series modules and Q series modules

When an ACPU module is replaced with a QCPU module, programs for the ACPU module can be used by changing the PLC type in GX Developer. However, the programs ... More Details >>
- No：22696
- Release Date：2018/09/03 17:29
- Update：2018/09/21 14:21
- Category： MELSEC-Q Series
How to check automatically assigned devices in GX Works2

Click the local label to be checked and select "Cross Reference" from the right-click menu to check the devices. More Details >>
- No：22700
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series
Input filter adjustment when a high-speed counter or the interrupt function is used

When a coil of the high-speed counter or an interrupt pointer is programmed, the programmable controller system adjusts the filter constant of the correspond... More Details >>
- No：24867
- Release Date：2019/04/15 08:06
- Category： MELSEC-F Series , High-Speed Counter
File format that can be saved to a CF card in the FX3U-CF-ADP

CSV file can be saved. More Details >>
- No：24938
- Release Date：2019/04/18 14:24
- Category： MELSEC-F Series , Main Unit , Accessories

791-800 of Total 1023

Inquiries

page top