PDO mapping is configured from the CC-Link IE TSN configuration settings. ① Open the CC-Link IE TSN configuration se

No, there is no function to resend all the data that could not be sent. By setting Retain and QoS from FB, it is possib

The maximum link points of the FX5-CCLIEF are 384 points each for RX/RY and 1024 points each for RWw/RWr.

Since they are octal, the number after Y7 is Y10 and after Y77 is Y100.

E-mail sending function is supported, but receiving function is not available.

The non-protocol communication can be set by the following two methods: (1) setting parameters using a programming tool,

Cyclic data is sometimes separated into new and old data by two words (32 bits) with auto refresh timing. Checking "Bloc

A link error has occurred in one of the slave stations in connection.Master station: Check the parameter again.Slave sta

I/O signals and buffer memory addresses need to be changed but data communications can be conducted using a FROM/TO inst

Make a space for comments in the parameter setting of the programmable controller with GX Developer.To write the created

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Programmable Controllers MELSEC

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(643)

CPU Module(179)
I/O Module(5)
Analog(16)
High-Speed Counter(14)
Motion/Positioning(11)
Network/Communication(97)
Option(9)
Engineering Software(61)
Safety Control(1)

Engineering Software(129)

FAQ within [ Programmable Controllers MELSEC ]

811-820 of Total 1010

prev 82 / 101page next

Regarding PDO Mapping Settings

PDO mapping is configured from the CC-Link IE TSN configuration settings. ① Open the CC-Link IE TSN configuration settings from the FX5-CCLGN-MS Basic Set... More Details >>
- No：44475
- Release Date：2024/07/02 19:07
- Category： MELSEC iQ-F Series , Network/Communication
Regarding the MQTT communication function retransmission function

No, there is no function to resend all the data that could not be sent. By setting Retain and QoS from FB, it is possible to resend only the latest message. More Details >>
- No：44368
- Release Date：2024/03/27 16:56
- Category： MELSEC iQ-F Series , Network/Communication
Regarding FX5-CCLIEF Maximum Link Points

The maximum link points of the FX5-CCLIEF are 384 points each for RX/RY and 1024 points each for RWw/RWr. More Details >>
- No：40020
- Release Date：2023/08/24 14:31
- Category： MELSEC iQ-F Series , Network/Communication
Output numbers of the FX programmable controllers

Since they are octal, the number after Y7 is Y10 and after Y77 is Y100. More Details >>
- No：24946
- Release Date：2019/04/18 14:26
- Category： MELSEC-F Series
E-mail sending/receiving function of the FX3U-ENET-L

E-mail sending function is supported, but receiving function is not available. More Details >>
- No：24930
- Release Date：2019/04/17 11:39
- Category： MELSEC-F Series , Network/Communication
Communication setting methods when the FX3U-232-BD is used

The non-protocol communication can be set by the following two methods: (1) setting parameters using a programming tool, such as GX Works2, or (2) writing da... More Details >>
- No：24773
- Release Date：2019/02/27 15:24
- Category： MELSEC-F Series , Engineering Software , Network/Communication
Refresh timing of bit data and word data in the same CC-Link station

Cyclic data is sometimes separated into new and old data by two words (32 bits) with auto refresh timing. Checking "Block data assurance per station" of the ... More Details >>
- No：23058
- Release Date：2018/09/03 17:31
- Category： Network related products
What makes the ERR LED flash in a CC-Link network

A link error has occurred in one of the slave stations in connection.Master station: Check the parameter again.Slave station: Reassess the power supply, the ... More Details >>
- No：23023
- Release Date：2018/09/03 17:31
- Category： Network related products
Using a FROM/TO instruction after AJ71UC24 is replaced with QJ71C24N

I/O signals and buffer memory addresses need to be changed but data communications can be conducted using a FROM/TO instruction and X/Y signals. More Details >>
- No：23017
- Release Date：2018/09/03 17:31
- Category： Network related products
Writing comments into a programmable controller

Make a space for comments in the parameter setting of the programmable controller with GX Developer.To write the created comments into a programmable control... More Details >>
- No：22962
- Release Date：2018/09/03 17:31
- Category： Engineering Software

811-820 of Total 1010

Inquiries

page top