For output terminals of a programmable controller, one common terminal is used for 1, 2, 4, or 8 output points. Each com

If the OUT instruction using the device number of the latch target device exists in a sequence program, the latched data

To update to firmware version “1.100 ” or higher, you need a product with serial number (S/N) or higher listed below. ・

Download the file directly under the C: drive and then install it.

The scan time may be substantially longer. Continue the operation if there is no problem with the longer scan time.

A runtime license is required for all personal computers on which MX Component operates.

GX Configurator-MB does not need to be purchased. Parameters can be set using GX Works2 alone.

Yes. They have the same pin layout.

The bits 0 to F of the special register SD1284 (Open request signal) correspond to the connection numbers 1 to 16. When

The following shows the major differences. - AJ65SBTB1-16TE - 1-wire terminal block, 1-common type - Maximum lo

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Programmable Controllers MELSEC

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(643)

CPU Module(179)
I/O Module(5)
Analog(16)
High-Speed Counter(14)
Motion/Positioning(11)
Network/Communication(97)
Option(9)
Engineering Software(61)
Safety Control(1)

Engineering Software(129)

FAQ within [ Programmable Controllers MELSEC ]

871-880 of Total 1010

prev 88 / 101page next

COM terminal for outputs

For output terminals of a programmable controller, one common terminal is used for 1, 2, 4, or 8 output points. Each common line is assigned with a different... More Details >>
- No：24780
- Release Date：2019/02/27 15:58
- Category： MELSEC-F Series , Main Unit
Data backup failure

If the OUT instruction using the device number of the latch target device exists in a sequence program, the latched data may be overwritten by execution of t... More Details >>
- No：24783
- Release Date：2019/02/27 16:16
- Category： MELSEC-F Series , Engineering Software , Main Unit
Regarding updating the FX5U/FX5UC CPU module to firmware version “1.100 ” or later

To update to firmware version “1.100 ” or higher, you need a product with serial number (S/N) or higher listed below. ・FX5UC-32MT/DS-TS and FX5UC-32MT/DSS-T... More Details >>
- No：44623
- Release Date：2024/11/28 16:14
- Category： MELSEC iQ-F Series , CPU Module
GX Works2 update installation procedure

Download the file directly under the C: drive and then install it. More Details >>
- No：22524
- Release Date：2018/09/03 17:28
- Update：2018/09/20 14:28
- Category： MELSEC-Q Series
Memory allocation for online change

The scan time may be substantially longer. Continue the operation if there is no problem with the longer scan time. More Details >>
- No：22575
- Release Date：2018/09/03 17:29
- Update：2018/09/20 17:01
- Category： MELSEC-Q Series
Runtime license for MX Component

A runtime license is required for all personal computers on which MX Component operates. More Details >>
- No：22657
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series
GX Configurator-MB for the MODBUS(R) interface module

GX Configurator-MB does not need to be purchased. Parameters can be set using GX Works2 alone. More Details >>
- No：22701
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series
FNC connector pin layout in L series I/O module and Q series I/O module

Yes. They have the same pin layout. More Details >>
- No：22774
- Release Date：2018/09/03 17:30
- Category： MELSEC-L Series
SD1284 of LCPU with built-in Ethernet port

The bits 0 to F of the special register SD1284 (Open request signal) correspond to the connection numbers 1 to 16. When the open request is sent, the corresp... More Details >>
- No：22784
- Release Date：2018/09/03 17:30
- Category： MELSEC-L Series
Differences between the AJ65SBTB1-16TE and AJ65SBTB1B-16TE1

The following shows the major differences. -AJ65SBTB1-16TE - 1-wire terminal block, 1-common type - Maximum load current: 0.1 A/point -Protection fu... More Details >>
- No：23083
- Release Date：2018/09/03 17:31
- Update：2018/09/26 13:16
- Category： Network related products

871-880 of Total 1010

Inquiries

page top