The rapid stop deceleration time of parameter block is applied.However, when the rapid stop deceleration time is set in

Change the direction with "[PA14] Rotation direction selection/travel direction selection".

Set "[Pr.3] Movement amount per rotation" to "36000000(360.00000degree)", and "[Pr.4] Unit magnification" to "1".The sam

Set the torque limit value in "[Cd.101] Torque output setting value" before the positioning start.The values of "[Pr.17]

No, execute "[Cd.5] Axis error reset" to cancel the error after eliminating the error cause.

Torque is limited by the lower set value of "[Pr.17] Torque limit setting value" and "[Cd.22] New torque value/forward n

The BUSY signal turns ON even when position control of movement amount "0" is executed.However, since the ON time is sho

The torque limit value can be changed regardless of JOG operation status.Set the new torque limit value with "[Cd.22] Ne

Yes. The speed can be changed during JOG operation.Set the new speed with "[Cd.14] New speed value", and then set "[Cd.1

Set "[Cd.16] Inching movement amount", and turn ON the Forward run JOG start signal or the Reverse run JOG start signal.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Motion Controllers > MELSEC iQ-R Series

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

MELSEC iQ-R Series

FAQ within [ MELSEC iQ-R Series ]

11-20 of Total 44

prev 2 / 5page next

Rapid stop signal

The rapid stop deceleration time of parameter block is applied.However, when the rapid stop deceleration time is set in the servo program, the value is enabl... More Details >>
- No：23557
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Motor rotation direction

Change the direction with "[PA14] Rotation direction selection/travel direction selection". More Details >>
- No：23554
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU
Electronic gear

Set "[Pr.3] Movement amount per rotation" to "36000000(360.00000degree)", and "[Pr.4] Unit magnification" to "1".The same result is obtained by setting "3600... More Details >>
- No：23586
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Torque limit

Set the torque limit value in "[Cd.101] Torque output setting value" before the positioning start.The values of "[Pr.17] Torque limit setting value" and "[Cd... More Details >>
- No：23583
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Warning

No, execute "[Cd.5] Axis error reset" to cancel the error after eliminating the error cause. More Details >>
- No：23580
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Torque limit

Torque is limited by the lower set value of "[Pr.17] Torque limit setting value" and "[Cd.22] New torque value/forward new torque value".When the current tor... More Details >>
- No：23621
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC
BUSY signal

The BUSY signal turns ON even when position control of movement amount "0" is executed.However, since the ON time is short, the ON status may not be detected... More Details >>
- No：23612
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M , QD74MH
Torque limit value change

The torque limit value can be changed regardless of JOG operation status.Set the new torque limit value with "[Cd.22] New torque value/forward new torque val... More Details >>
- No：23609
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD74MH
Speed change during JOG operation

Yes. The speed can be changed during JOG operation.Set the new speed with "[Cd.14] New speed value", and then set "[Cd.15] Speed change request" to "1". More Details >>
- No：23606
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Inching operation

Set "[Cd.16] Inching movement amount", and turn ON the Forward run JOG start signal or the Reverse run JOG start signal. More Details >>
- No：23590
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M

11-20 of Total 44

Inquiries

page top