It depends on the servo error.Some can be cleared by "[Cd.5] Axis error reset" but the other cannot unless the servo amp

The torque limit value can be changed regardless of JOG operation status.Set the new torque limit value with "[Cd.22] Ne

Set "[Pr.45] Home position address (72+150n, 73+150n)" of the basic parameters for home position return.Set by 2 words.T

Error 108 (Start not possible) occurs when a start is requested while a stop signal is ON.Check the "[Md.26] Axis operat

Error 2035 (Command frequency error) occurs when the servo amplifier detects a command frequency error. (1) When the com

Error1201 (HPR data incorrect) occurs when the backup data for absolute position restoration is lost.Execute the machine

Error 1205 (SSCNET communication error) occurs when erroneous data is received from servo amplifier. [When the servo pa

It depends on the setting of servo parameter "[PA03] Absolute position detection system" whether the HPR request flag ("

Yes. You can check the servo status through the following monitor data. • "[Md.108] Servo status 1" • "[Md.125] Servo

Torque is limited by the lower set value of "[Pr.17] Torque limit setting value" and "[Cd.22] New torque value/forward n

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Controllers

Programmable Automation Controllers MELSEC(28)

MELSEC MX Controller MX-R Model
MELSEC MX Controller MX-F Model(28)
MELSEC MX Controller Engineering Software
Programmable Controllers MELSEC(1702)

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(643)
MELSEC-Q Series(213)
MELSEC-L Series(105)
MELSEC-F Series(457)
Network related products(110)
Engineering Software(129)

Motion Controllers(414)

MELSEC iQ-R Series(73)
MELSEC iQ-F Series(29)
MELSEC-Q Series(247)
MELSEC-L Series(64)
Engneering software(1)

FAQ within [ Controllers ]

21-30 of Total 1110

prev 3 / 111page next

Axis error reset

It depends on the servo error.Some can be cleared by "[Cd.5] Axis error reset" but the other cannot unless the servo amplifier's power is turned OFF.Refer to... More Details >>
- No：23584
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Torque limit value change

The torque limit value can be changed regardless of JOG operation status.Set the new torque limit value with "[Cd.22] New torque value/forward new torque val... More Details >>
- No：23609
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD74MH
Home position address

Set "[Pr.45] Home position address (72+150n, 73+150n)" of the basic parameters for home position return.Set by 2 words.The value will be reflected when PLC r... More Details >>
- No：23599
- Release Date：2018/09/14 15:09
- Category： FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M , QD74MH
Error 108

Error 108 (Start not possible) occurs when a start is requested while a stop signal is ON.Check the "[Md.26] Axis operation status".If "20: Servo amplifier ... More Details >>
- No：23613
- Release Date：2018/09/14 15:09
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M , QD74MH
Error 2035

Error 2035 (Command frequency error) occurs when the servo amplifier detects a command frequency error. (1) When the command from the controller is the permi... More Details >>
- No：23616
- Release Date：2018/09/14 15:09
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M , QD74MH
Error 1201

Error1201 (HPR data incorrect) occurs when the backup data for absolute position restoration is lost.Execute the machine home position return after checking ... More Details >>
- No：23604
- Release Date：2018/09/14 15:09
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M , QD74MH
Error 1205

Error 1205 (SSCNET communication error) occurs when erroneous data is received from servo amplifier. [When the servo parameter "[PA14] Rotation direction se... More Details >>
- No：23614
- Release Date：2018/09/14 15:09
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
HPR request flag

It depends on the setting of servo parameter "[PA03] Absolute position detection system" whether the HPR request flag ("[Md.31] Status": b3) turns ON or not.... More Details >>
- No：23617
- Release Date：2018/09/14 15:09
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Servo status

Yes. You can check the servo status through the following monitor data. • "[Md.108] Servo status 1" • "[Md.125] Servo status 3" (QD77MS, LD77MS, LD77MH) ... More Details >>
- No：23588
- Release Date：2018/09/14 15:09
- Update：2023/03/09 10:02
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Torque limit

Torque is limited by the lower set value of "[Pr.17] Torque limit setting value" and "[Cd.22] New torque value/forward new torque value".When the current tor... More Details >>
- No：23591
- Release Date：2018/09/14 15:09
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD74MH

21-30 of Total 1110

Inquiries

page top