The FX5 CPU module does not support EtherCAT communication. There are no products in the FX series or iQ-F series that s

Refer to "b2: Command in-position flag" of "[Md.31] Status".

No. To execute continuous positioning and continuous trajectory control, the same target axes and the same number of con

Yes, the time can be changed during operation by using the acceleration/deceleration time change function. Set the accel

Yes.Beginning with the device in the "Device/Label Automatic-Assign Setting" window, devices are assigned in descending

Download the file directly under the C: drive and then install it.

Unless the necessity is described in manuals, a noise filter is not required. However, if the programmable controller i

Yes. You can check the servo status through the following monitor data. • "[Md.108] Servo status 1" • "[Md.125] Servo st

Set "[Pr.3] Movement amount per rotation" to "36000000(360.00000degree)", and "[Pr.4] Unit magnification" to "1".The sam

It depends on the setting of servo parameter "[PA03] Absolute position detection system" whether the HPR request flag ("

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Controllers

Programmable Automation Controllers MELSEC(28)

MELSEC MX Controller MX-R Model
MELSEC MX Controller MX-F Model(28)
MELSEC MX Controller Engineering Software
Programmable Controllers MELSEC(1731)

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(672)
MELSEC-Q Series(213)
MELSEC-L Series(105)
MELSEC-F Series(457)
Network related products(110)
Engineering Software(129)

Motion Controllers(414)

MELSEC iQ-R Series(73)
MELSEC iQ-F Series(29)
MELSEC-Q Series(247)
MELSEC-L Series(64)
Engneering software(1)

FAQ within [ Controllers ]

71-80 of Total 1123

prev 8 / 113page next

Regarding EtherCAT Communications

The FX5 CPU module does not support EtherCAT communication. There are no products in the FX series or iQ-F series that support EtherCAT communication. More Details >>
- No：39313
- Release Date：2023/02/14 08:54
- Category： MELSEC iQ-F Series , CPU Module , Network/Communication
Command in-position

Refer to "b2: Command in-position flag" of "[Md.31] Status". More Details >>
- No：23598
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Linear and circular interpolation

No. To execute continuous positioning and continuous trajectory control, the same target axes and the same number of control axes must be specified in the po... More Details >>
- No：23582
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Acceleration/deceleration time change

Yes, the time can be changed during operation by using the acceleration/deceleration time change function. Set the acceleration/deceleration time change para... More Details >>
- No：23569
- Release Date：2018/09/14 15:09
- Category： RnMTCPU
Automatically assigned devices in GX Works2

Yes.Beginning with the device in the "Device/Label Automatic-Assign Setting" window, devices are assigned in descending order (from the greatest device numbe... More Details >>
- No：22846
- Release Date：2018/09/03 17:30
- Category： Engineering Software
GX Works2 update installation procedure

Download the file directly under the C: drive and then install it. More Details >>
- No：22524
- Release Date：2018/09/03 17:28
- Update：2018/09/20 14:28
- Category： MELSEC-Q Series
Necessity for installing a noise filter

Unless the necessity is described in manuals, a noise filter is not required. However, if the programmable controller is used in an environment with much no... More Details >>
- No：22283
- Release Date：2018/08/30 13:48
- Category： MELSEC-F Series , Main Unit , I/O Extension , Analog Control , High-Speed Counting , Positioning Control , Network/Communication , Accessories
Servo status

Yes. You can check the servo status through the following monitor data. • "[Md.108] Servo status 1" • "[Md.125] Servo status 3" (QD77MS, LD77MS, LD77MH) ... More Details >>
- No：23588
- Release Date：2018/09/14 15:09
- Update：2023/03/09 10:02
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Electronic gear

Set "[Pr.3] Movement amount per rotation" to "36000000(360.00000degree)", and "[Pr.4] Unit magnification" to "1".The same result is obtained by setting "3600... More Details >>
- No：23586
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
HPR request flag

It depends on the setting of servo parameter "[PA03] Absolute position detection system" whether the HPR request flag ("[Md.31] Status": b3) turns ON or not.... More Details >>
- No：23617
- Release Date：2018/09/14 15:09
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M

71-80 of Total 1123

Inquiries

page top