Short between SDA and RDA and between SDB and RDB, and then connect them to + (Data-A) and - (Data-B) on the external de

If each master module controls their own CC-Link networks, all master modules can be set as station 0 even though they a

Receiving data overwrites the buffer memory data. Writing 0 with a program can be performed but is unnecessary as the da

The MODE switch can set the following modes.- 0 to 4: Online mode- 5 to 9: Line test mode- A to E: Hardware test modeEac

The overall cable distance and station-to-station distance depend on the version and the transmission speed. Figure 1 s

A CC-Link slave station number can be skipped by assigning the skipped number to a reserved station. A reserved station

The data link status is stored in SW80 to SW83.Each bit corresponds to a station number and a bit turns ON if the corres

X and Y assignments are as follows.- X0 to XF- Y10 to Y1F

Major differences in input specifications are shown below. - AJ65SBTB1-16DT - Rated input current approx. 7 mA - ON

Possible causes are as follows.(1) Another master station exists on the same line.(2) Noise is detected on the line at p

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Controllers

Programmable Controllers MELSEC(1637)

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(578)
MELSEC-Q Series(213)
MELSEC-L Series(105)
MELSEC-F Series(457)
Network related products(110)
Engineering Software(129)
Motion Controllers(414)

MELSEC iQ-R Series(73)
MELSEC iQ-F Series(29)
MELSEC-Q Series(247)
MELSEC-L Series(64)
Engneering software(1)

FAQ within [ Controllers ]

451-460 of Total 1055

prev 46 / 106page next

RS-485 connection between QJ71C24N and an external device

Short between SDA and RDA and between SDB and RDB, and then connect them to + (Data-A) and - (Data-B) on the external device. More Details >>
- No：22986
- Release Date：2018/09/03 17:31
- Category： Network related products
CC-Link master module settings

If each master module controls their own CC-Link networks, all master modules can be set as station 0 even though they are controlled by the same CPU. More Details >>
- No：23008
- Release Date：2018/09/03 17:31
- Category： Network related products
Clearing data in the QJ71C24N's receiving area buffer memory

Receiving data overwrites the buffer memory data. Writing 0 with a program can be performed but is unnecessary as the data is overwritten. More Details >>
- No：23009
- Release Date：2018/09/03 17:31
- Category： Network related products
MODE switch setting for QJ61BT11N

The MODE switch can set the following modes.- 0 to 4: Online mode- 5 to 9: Line test mode- A to E: Hardware test modeEach mode in ascending order of set valu... More Details >>
- No：23025
- Release Date：2018/09/03 17:31
- Category： Network related products
Overall cable distance and station-to-station distance in CC-Link networks

The overall cable distance and station-to-station distance depend on the version and the transmission speed. Figure 1 shows the case with Ver.1.10-compatibl... More Details >>
- No：23028
- Release Date：2018/09/03 17:31
- Update：2018/09/26 10:14
- Category： Network related products
Setting required to skip CC-Link slave station numbers

A CC-Link slave station number can be skipped by assigning the skipped number to a reserved station. A reserved station is counted as one of all the connecte... More Details >>
- No：23029
- Release Date：2018/09/03 17:31
- Category： Network related products
How to check link errors in CC-Link slave stations

The data link status is stored in SW80 to SW83.Each bit corresponds to a station number and a bit turns ON if the corresponding station causes a data link er... More Details >>
- No：23031
- Release Date：2018/09/03 17:31
- Category： Network related products
Assigning X and Y signals of AJ65SBTB1-32DT

X and Y assignments are as follows.- X0 to XF- Y10 to Y1F More Details >>
- No：23034
- Release Date：2018/09/03 17:31
- Category： Network related products
Difference between AJ65SBTB1-16DT and AJ65SBTB1-16DT1

Major differences in input specifications are shown below. - AJ65SBTB1-16DT - Rated input current approx. 7 mA - ON voltage/ON current 14 VDC or higher/... More Details >>
- No：23035
- Release Date：2018/09/03 17:31
- Update：2018/09/26 10:24
- Category： Network related products
Duplication error in a CC-Link master station

Possible causes are as follows.(1) Another master station exists on the same line.(2) Noise is detected on the line at power on. More Details >>
- No：23044
- Release Date：2018/09/03 17:31
- Category： Network related products

451-460 of Total 1055

Inquiries

page top