The inverter overcurrent shut-off fault indication E.OC1, E.OC2, or E.OC3 is not only displayed when the inverter output

Measure the megger values on the inverter's output side.If there is no problem:If the motor capacity is extremely smalle

The regenerative overvoltage shutoff protective function is provided since the terminal voltage of the internal capacito

While the FREQROL-Z200 series and A500 series have a brake resistor built in the capacity up to 7.5K, the FREQROL-E500 s

Rapid blinking of the RUN LED suggests that the frequency is not set correctly.When the operation mode setting of Pr.79

The alarm E7 occurs when the forced stop signal of the servo system controller is enabled. Ensure the safety and cancel

"PS" is displayed when the inverter is stopped with the "STOP/RESET" button from PU. The PU stop (PS) release method is

"OL" stands for "overload". Whenever current of 150% or more of the inverter rated current flows, "OL" is ON. If you con

The possible causes of the error UVT are as follows.- Low power supply voltage - Insufficient power supply capacity - Da

E.OP1 indicates the communication line error. E.1 indicates a hardware fault of the communication option. (It is judged

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

1-10 of Total 1368

prev 1 / 137page next

Error

The inverter overcurrent shut-off fault indication E.OC1, E.OC2, or E.OC3 is not only displayed when the inverter output current reaches approximately 200% o... More Details >>
- No：21519
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A200
Error E.LF

Measure the megger values on the inverter's output side.If there is no problem:If the motor capacity is extremely smaller than the inverter capacity (as a gu... More Details >>
- No：21933
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-E500
E．OV2 error

The regenerative overvoltage shutoff protective function is provided since the terminal voltage of the internal capacitor of the inverter can rise abnormally... More Details >>
- No：21544
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL
Deceleration overvoltage (E.OV3)

While the FREQROL-Z200 series and A500 series have a brake resistor built in the capacity up to 7.5K, the FREQROL-E500 series does not have a built-in brake ... More Details >>
- No：21993
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E500
RUN blinks

Rapid blinking of the RUN LED suggests that the frequency is not set correctly.When the operation mode setting of Pr.79 is changed, the entrance point of the... More Details >>
- No：21757
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Alarm E7

The alarm E7 occurs when the forced stop signal of the servo system controller is enabled. Ensure the safety and cancel the forced stop signal of the control... More Details >>
- No：23647
- Release Date：2018/09/14 15:10
- Category： MELSERVO-J4 , MELSERVO-JE
PS display

"PS" is displayed when the inverter is stopped with the "STOP/RESET" button from PU. The PU stop (PS) release method is as follows. (1) Release method using ... More Details >>
- No：21264
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Meaning of OL display

"OL" stands for "overload". Whenever current of 150% or more of the inverter rated current flows, "OL" is ON. If you continue operation with "OL" is displaye... More Details >>
- No：21449
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-V200
Error "E.UVT" (undervoltage protection)

The possible causes of the error UVT are as follows.- Low power supply voltage - Insufficient power supply capacity - Damage or failure Check the power suppl... More Details >>
- No：21295
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Error of the communication option

E.OP1 indicates the communication line error. E.1 indicates a hardware fault of the communication option. (It is judged as the hardware fault when the commun... More Details >>
- No：20805
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , Plug-in Options

1-10 of Total 1368

Inquiries

page top